2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B132833
    Disengage the 2 clips and remove the front door lower frame bracket garnish.


2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B132834E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.


3. REMOVE ASSIST GRIP COVER

  1. B132836E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the assist grip cover.


4. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. B132838E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B132840E01
    Remove the 3 screws and clip (A).

  1. Using a clip remover, disengage the 9 clips.

  1. B136401E01
    Pull up the front door trim board in the direction indicated by the arrow.

  1. Disengage the reference bosses from the front door panel.

  1. Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.

  1. B136403
    Disengage the 2 claws and disconnect the front door inside handle sub-assembly.


6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B136404
    Using a screwdriver, disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.


7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B136408
    Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door inside handle sub-assembly.


8. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

  1. E129164
    Disconnect the connector.

  1. Remove the 4 bolts and front No. 1 speaker assembly.

    NOTICE:
    Do not touch the cone part of the speaker.


9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

  1. B149066
    Disconnect the connector.

  1. Remove the 3 nuts and the outer rear view mirror assembly.


10. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B136410E01
    Disconnect the connector and each clamp, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door.


11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the front power window regulator motor assembly connector.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. B136412
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, the door glass may fall, causing damage.

  1. B136413E01
    Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.

  1. Disconnect the power window regulator master switch assembly and front power window regulator motor assembly connector.


12. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

  1. B137001E01
    Fully open the front door glass.

  1. Put protective tape around the front door belt moulding assembly.

  1. B137002
    Using a moulding remover, disengage the 2 clips and 5 claws, and remove the front door belt moulding assembly.

    HINT:
    Tape the remover tip before use.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front and rear ends of the moulding.


13. REMOVE FRONT DOOR GLASS RUN

  1. B136418
    Remove the front door glass run.


14. REMOVE FRONT DOOR WEATHERSTRIP

  1. B129816
    Using a clip remover, disengage the clip and remove the front door weatherstrip.

    HINT:
    Tape the clip remover tip before use.


15. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and moulding excessively.

  1. Using a heat light, heat the front door rear window frame moulding.

  1. B137005
    Disengage the clip.

  1. B137006E01
    Using a moulding remover, remove the front door rear window frame moulding.


16. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

  1. B137008E01
    Put a 4 mm (0.16 in.) drill bit into a drill.

  1. Tape the drill bit without the portion of 5 mm (0.20 in.) from the tip covered.

    HINT:
    Tape the drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the rivets, drill off the flanges of the rivets, and remove the 7 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivets with the drill, because this may cause damage to the installation holes of the rivets or the drill bit.
    3. Be careful when touching the drilled rivets as they may become hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Remove the front door upper window frame moulding from the door frame.

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →