2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B136443E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


2. REMOVE DOOR ASSIST GRIP COVER

  1. B149028E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.


3. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. B146097E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B136451
    Remove the 3 screws.

  1. Using a clip remover, disengage the 7 clips.

  1. B136452
    Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

  1. Disconnect the connector.

  1. B136453
    Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

  1. B141704
    Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.


5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

  1. B136456
    Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.


6. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B136459
    Disconnect the cables and remove the rear door inside handle sub-assembly.


7. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B149017
    Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the tape remaining on the door.


8. REMOVE REAR DOOR GLASS RUN

  1. B136466
    Remove the rear door glass run.


9. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

  1. B136467
    Remove the 2 bolts, the screw, and the rear door lower window frame sub-assembly.


10. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B136468
    Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B146103
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


12. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

  1. B137003E01
    Fully open the rear door glass.

  1. Put protective tape around the rear door belt moulding assembly.

  1. B137004
    Using a moulding remover, disengage the clip and 6 claws, and remove the rear door belt moulding assembly.

    HINT:
    Tape the remover tip before use.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front end of the moulding.


13. REMOVE REAR DOOR WEATHERSTRIP

  1. B129819
    Using a clip remover, disengage the clip and remove the rear door weatherstrip.

    HINT:
    Tape the clip remover tip before use.


14. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and moulding excessively.

  1. Using a heat light, heat the rear door front window frame moulding.

  1. B137009
    Disengage the clip.

  1. B137010E01
    Using a moulding remover, remove the rear door front window frame moulding.


15. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

  1. B137012E01
    Put a 4 mm (0.16 in.) drill bit into a drill.

  1. Tape the drill bit without the portion of 5 mm (0.20 in.) from the tip covered.

    HINT:
    Tape the drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 7 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.
    3. Be careful when touching the drilled rivets, as they may become hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Remove the rear door upper window frame moulding from the door frame.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Jun 2006 – Sep 2006) →