2006-2011 Camry Aurion · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

A107881E30

HINT:
The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of the terminals, and displayed in the "Specified Conditions" column. The illustration above can be used as a reference to identify the ECM terminal locations.

Symbol (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BATT (A24-20) - E1 (C24-104)
Y - W-B
Battery (for measuring battery voltage and for ECM memory)
Always
9 to 14 V
+B (A24-2) - E1 (C24-104)
R - W-B
Power source of ECM
Ignition switch on (IG)
9 to 14 V
+B2 (A24-1) - E1 (C24-104)
R - W-B
Power source of ECM
Ignition switch on (IG)
9 to 14 V
+BM (A24-3) - E1 (C24-104)
LG - W-B
Power source of throttle actuator
Always
9 to 14 V
IGT1 (C24-85) - E1 (C24-104)
IGT2 (C24-84) - E1 (C24-104)
IGT3 (C24-83) - E1 (C24-104)
IGT4 (C24-82) - E1 (C24-104)
W - W-B
G-R - W-B
G - W-B
LG - W-B
Ignition coil
(ignition signal)
Idling
Pulse generation
(see waveform 1)
IGF1 (C24-81) - E1 (C24-104)
BR - W-B
Ignition coil
(ignition confirmation signal)
Ignition switch on (IG)
4.5 to 5.5 V
Idling
Pulse generation
(see waveform 1)
NE+ (C24-122) - NE- (C24-121)
G - R
Crankshaft position sensor
Idling after engine warmed-up
Pulse generation
(see waveform 2)
G2+ (C24-99) - G2- (C24-98)
Y - BR
Camshaft position sensor
Idling after engine warmed-up
Pulse generation
(see waveform 2)
#10 (C24-108) - E01 (C24-45)
#20 (C24-107) - E01 (C24-45)
#30 (C24-106) - E01 (C24-45)
#40 (C24-105) - E01 (C24-45)
B - W-B
R - W-B
Y - W-B
L - W-B
Injector
Ignition switch on (IG)
9 to 14 V
Idling
Pulse generation
(see waveform 3)
HA1A (C24-109) - E04 (C24-46)
G - W
A/F sensor heater
Ignition switch on (IG)
9 to 14 V
Idling
Below 3.0 V
A1A+ (C24-112) - E1 (C24-104)
L - W-B
A/F sensor
Idling
Below 3.3 V*1
A1A- (C24-113) - E1 (C24-104)
P - W-B
A/F sensor
Idling
Below 3.0 V*1
HT1B (C24-47) - E03 (C24-86)
LG - B
Heated oxygen sensor heater
Ignition switch on (IG)
9 to 14 V
Idling
Below 3.0 V
OX1B (C24-64) - EX1B (C24-87)
W - BR
Heated oxygen sensor
Maintain engine speed at 2,500 rpm for 2 minutes after warming up sensor
Pulse generation
(see waveform 4)
KNK1 (C24-110) - EKNK (C24-111)
G - R
Knock sensor
Engine speed maintained at 4,000 after warming up engine
Pulse generation
(see waveform 5)
SPD (A24-8) - E1 (C24-104)
L - W-B
Speed signal from combination meter
Driving at 20 km/h (12 mph)
Pulse generation
(see waveform 6)
THW (C24-97) - ETHW (C24-96)
B - P
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
THA (C24-65) - ETHA (C24-88)
P - Y
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
VG (C24-118) - E2G (C24-116)
SB - W
Mass air flow meter
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
W (A24-24) - E1 (C24-104)
BR - W-B
MIL
Ignition switch on (IG) (MIL goes off)
Below 3.0 V
Idling
9 to 14 V
STA (A24-48) - E1 (C24-104)
V - W-B
Starter signal
Cranking
5.5 V or more
NSW (C24-52)*2 - E1 (C24-104)
SB - W-B
Park/neutral position switch signal
Ignition switch on (IG), Shift lever position P or N
0.5 to 3.0 V
Ignition switch on (IG), Shift lever position other than P or N
9 to 14 V
ACCR (A24-13)*3 - E1 (C24-104)
B - W-B
ACC relay control signal
Cranking
Below 1.5 V
STSW (A24-14)*3 - E1 (C24-104)
R - W-B
Starter relay operation signal
Cranking
9 to 14 V
VTA1 (C24-115) - ETA (C24-91)
Y - P
Throttle position sensor (for engine control)
Ignition switch on (IG), Throttle valve fully closed
0.5 to 1.2 V
Ignition switch on (IG), Throttle valve fully open
3.2 to 4.8 V
VTA2 (C24-114) - ETA (C24-91)
W-L - P
Throttle position sensor (for sensor malfunction detection)
Ignition switch on (IG), Accelerator pedal released
2.1 to 3.1 V
Ignition switch on (IG), Accelerator pedal depressed
4.5 to 5.5 V
VCTA (C24-67) - ETA (C24-91)
B - P
Power source of sensor (specific voltage)
Ignition switch on (IG)
4.5 to 5.5 V
VCPA (A24-57) - EPA (A24-59)
B - Y
Power source of accelerator pedal position sensor (for VPA)
Ignition switch on (IG)
4.5 to 5.5 V
VPA (A24-55) - EPA (A24-59)
G - Y
Accelerator pedal position sensor (for engine control)
Ignition switch on (IG), Accelerator pedal released
0.5 to 1.1 V
Ignition switch on (IG), Accelerator pedal fully depressed
2.6 to 4.5 V
VPA2 (A24-56) - EPA2 (A24-60)
R - BE
Accelerator pedal position sensor (for sensor malfunctioning detection)
Ignition switch on (IG), Accelerator pedal released
1.2 to 2.0 V
Ignition switch on (IG), Accelerator pedal fully depressed
3.4 to 5.0 V
VCP2 (A24-58) - EPA2 (A24-60)
L - BE
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch on (IG)
4.5 to 5.0 V
M+ (C24-42) - ME01 (C24-43)
G - B
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 7)
M- (C24-41) - ME01 (C24-43)
R - B
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 8)
STP (A24-36) - E1 (C24-104)
W - W-B
Stop light switch
Brake pedal depressed
9 to 14 V
Brake pedal released
Below 1.5 V
ST1- (A24-35) - E1 (C24-104)
GR - W-B
Stop light switch
Ignition switch on (IG), Brake pedal depressed
Below 1.5 V
Ignition switch on (IG), Brake pedal released
9 to 14 V
PRG (C24-49) - E1 (C24-104)
BE - W-B
Purge VSV
Ignition switch on (IG)
9 to 14 V
Idling
Pulse generation
(see waveform 9)
FC (A24-7) - E1 (C24-104)
Y - W-B
Fuel pump control
Ignition switch on (IG)
9 to 14 V
Idling
Below 1.5 V
TACH (A24-15) - E1 (C24-104)
B - W-B
Engine speed
Idling
Pulse generation
(see waveform 10)
TC (A24-27) - E1 (C24-104)
P - W-B
Terminal TC of DLC3
Ignition switch on (IG)
9 to 14 V
OC1+ (C24-100) - OC1- (C24-123)
W - B
Camshaft timing oil control valve (OCV)
Idling
Pulse generation
(see waveform 11)
CANH (A24-41) - E1 (C24-104)
B - W-B
CAN communication line
Ignition switch on (IG)
Pulse generation
(see waveform 12)
CANL (A24-49) - E1 (C24-104)
W - W-B
CAN communication line
Ignition switch on (IG)
Pulse generation
(see waveform 13)
FANL (A24-21) - E1 (C24-104)
R - W-B
FAN NO. 3 relay
Ignition switch on (IG)
9 to 14 V
Idling with A/C ON
or
High engine coolant temperature
Below 1.5 V
FANH (A24-22) - E1 (C24-104)
W - W-B
FAN NO. 1, 2 relay
Idling with high engine coolant temperature
Below 1.5 V
IGSW (A24-28) - E1 (C24-104)
Y - W-B
Ignition switch
Ignition switch on (IG)
9 to 14 V
MREL (A24-44) - E1 (C24-104)
BE - W-B
EFI MAIN relay
Ignition switch on (IG)
9 to 14 V

HINT:
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
*2: Automatic transaxle only
*3: With smart entry and start system


WAVEFORM 1
A122717E03
Igniter IGT signal (from ECM to igniter) 
ECM Terminal Name
Between IGT (1 to 4) and E1
Between IGF1 and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A063955E23
Crankshaft position sensor and Camshaft position sensor 
ECM Terminal Name
CH1: Between G2+ and G2-
CH2: Between NE+ and NE-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idle after engine warmed-up

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 3
A093279E10
Injector No. 1 (to No. 4) injector signal 
ECM Terminal Name
Between #10 (to #40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 4
A088863E15
Heated oxygen sensor (bank 1 sensor 2) 
ECM Terminal Name
Between OX1B and EX1B
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Maintain engine speed at 2,500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, the items O2S B1 S2 show the values input to the ECM from the heated oxygen sensor.


WAVEFORM 5
A085286E24
Knock sensor 
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after engine warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 6
A005135E29
Vehicle speed signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 7
A093274E14
Throttle actuator positive terminal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idle with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 8
A093275E13
Throttle actuator negative terminal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idle with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 9
A105220E03
Purge VSV 
ECM Terminal Name
Between PRG and E1
Tester Range
5 V/DIV., 50 ms./DIV.
Condition
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10
A093225E11
Engine speed signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 11
A093229E11
Camshaft timing oil control valve (OCV) 
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 12
A086154E12
CAN communication signal 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Ignition switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 13
A086155E13
CAN communication signal 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Ignition switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.

← TERMINALS OF ECM (Jun 2006 – May 2009)DIAGNOSIS SYSTEM (Jun 2006 – Sep 2006) →