2006-2011 Camry Aurion · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
Actual vehicle speed
The speed indicated on the speedometer.
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
  1. 850 to 950 rpm: Idling (M/T)
  2. 610 to 710 rpm: Idling (A/T)
-
Calculate Load
Load calculated by ECM/
Min.: 0%, Max.: 100%
  1. 3.3 to 26.7%: Idling
  2. 12 to 14.7%: Running without load at 2500 rpm
-
Vehicle Load*3
Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load
-
MAF
Air flow rate from mass air flow meter/
Min.: 0 gm/sec., Max.: 655.35 gm/sec.
  1. 0.54 to 4.33 gm/sec.: Idling (M/T)
  2. 0.58 to 4.67 gm/sec.: Idling (A/T)
  3. 3.33 to 9.17 gm/sec.: Running without load at 2500 rpm
If the value is approximately 0.0 gm/sec.:
  1. The mass air flow meter power source circuit is open.
  2. VG circuit is open or shorted.
If 271.0 gm/sec. or more:
  1. The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa (0 mmHg), Max.: 255 kPa (1912.5 mmHg)
Approximately 100 kPa: ignition switch on (IG)
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 215°C (419°F)
80 to 100°C (176 to 212°F): After warming up
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Equivalent to ambient air temperature
If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F) or higher, the sensor circuit is shorted.
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Service data
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F)
Coolant temperature when engine started
Service data
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F)
Intake air temperature when engine started
Service data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
-
Accel Sens. No. 1 Volt %
Absolute accelerator pedal position No. 1/
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal released
52 to 90%: Accelerator pedal fully depressed
-
Accel Sens. No. 2 Volt %
Absolute accelerator pedal position No. 2/
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal released
68 to 100%: Accelerator pedal fully depressed
-
Accel Sensor Out No. 1
Accelerator pedal position sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
-
-
Accel Sensor Out No. 2
Accelerator pedal position sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
-
-
Accel Sensor Out No. 1
Accelerator pedal position sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No. 2
Accelerator pedal position sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
1.2 to 2.0 V: Accelerator pedal released
3.4 to 5.0 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling
-
Accel Fully Close #1 (AD)
APP sensor No. 1 voltage (AD):
Min.: 0 V, MAX.: 4.9804 V
-
ETCS service data
Accel Fully Close Learn #1
Accelerator fully closed learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data
Accel Fully Close Learn #2
Accelerator fully closed learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data
Throttle Sensor Volt %
Throttle valve opening percentage according to throttle position sensor/
Min.: 0%, Max.: 100%
  1. 10 to 22%: Accelerator pedal released
  2. 66 to 98%: Accelerator pedal fully depressed
Value calculated based on the voltage at terminal VTA1
Throttl Sensor #2 Volt %
Throttle valve opening percentage according to throttle position sensor No. 2/
Min.: 0%, Max.: 100%
  1. 42 to 62%: Accelerator pedal released
  2. 92 to 100%: Accelerator pedal fully depressed
Value calculated based on the voltage at terminal VTA2
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal released
-
System Guard
System guard/
ON or OFF
-
ETCS service data
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
  1. ON: Accelerator pedal released
  2. OFF: Accelerator pedal fully depressed
-
Throttle Require Position
Throttle requirement position/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.0 V: Idling
-
Throttle Sensor Position*1
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
  1. 0%: Accelerator pedal released
  2. 50 to 80%: Accelerator pedal fully depressed
Recognition value for throttle opening angle on ECM
Throttle Position No. 1
Throttle position No. 1/
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Position No. 2
Throttle position No. 2/
Min.: 0 V, Max.: 4.98 V
-
-
Throttle Position No. 1
Throttle position No. 1/
Min.: 0 V, Max.: 4.98 V
  1. 0.5 to 1.1 V: Accelerator pedal released
  2. 3.2 to 4.9 V: Accelerator pedal fully depressed
  3. 0.6 to 1.4 V: Fail-safe operating
-
Throttle Position No. 2
Throttle position No. 2/
Min.: 0 V, Max.: 4.98 V
  1. 2.1 to 3.1 V: Accelerator pedal released
  2. 4.6 to 5.0 V: Accelerator pedal fully depressed
  3. 2.1 to 3.1 V: Fail-safe operating
-
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
0.5 to 4.9 V
-
Throttle Sens Open Pos #1
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Throttle Sens Open Pos #2
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
-
ETCS service data
Throttle Sens Open #1 (AD)
Throttle position sensor No. 1 output voltage (AD):
Min.: 0 V, Max.: 4.9804 V
0.5 to 4.9 V
Read value with ignition switch on (IG)
Throttle Motor
Whether throttle actuator control permitted:
ON or OFF
ON: Idling
Read value with ignition switch on (IG)
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
ETCS service data
Throttle Motor DUTY
Throttle actuator/
Min.: 0%, Max.: 100%
0.5 to 40%: Idling
ETCS service data
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
-
ETCS service data
Throttle Motor Open Duty
Throttle actuator open duty ratio/
Min.: 0%, Max.: 100%
-
ETCS service data
Throttle Motor Close Duty
Throttle actuator closed duty ratio/
Min.: 0%, Max.: 100%
-
ETCS service data
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data
Throttle Fully Close Learn
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.98 V
0.4 to 0.8 V: Accelerator pedal released
-
ETCS Actuator Power
ETCS power supply:
ON or OFF
ON: ignition switch on (IG) and system normal
-
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 79.998 V
9 to 14 V: Ignition switch on (IG) and system normal
-
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Idling
ETCS service data
Clutch Current
Clutch current/
Min.: 0 A, Max.: 2.49 A
-
ETCS service data
Fail Safe Drive
Whether or not fail safe function executed:
ON or OFF
ON: ETCS has failed
-
Fail Safe Drive (Main CPU)
Whether or not fail safe function executed:
ON or OFF
ON: ETCS has failed
-
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 ms, Max.: 32.64 ms
1.92 to 3.37 ms: Idling
-
Injection Volum (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.15 ml: Idling
The quantity of fuel injection volume for 10 times
Fuel Pump/Speed Status
Fuel pump/speed status/
ON or OFF
ON: Engine running
The Active Test support data
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
0 to 50%: Idling, under purge control
The order signal from the ECM
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
0 to 10%: Idling
-
Purge Density Learn Value
Learned value of purge density/
Min.: -200, Max.: 199.993
-40 to 10: Idling
Service data
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
The Active Test support data
Target Air-Fuel Ratio
Air fuel ratio/
Min.: 0, Max.: 1.99
0.8 to 1.2: During idling
-
AF Lambda B1S1
Short-term fuel trim (for bank 1 sensor 1)/
Min.: 0, Max.: 1.99
  1. Value less than 1 (0.000 to 0.999) = Rich
  2. 1 = Stoichiometric air fuel ratio
  3. Value more than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage (for bank 1 sensor 1)/
Min.: 0 V, Max.: 7.99 V
2.6 to 3.8 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
AFS Current B1S1
Air fuel ratio sensor current (for bank 1 sensor 1)/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor.
O2S B1S2
Heated oxygen sensor output voltage (for bank 1 sensor 2)/
Min.: 0 V, Max.: 1.275 V
0.1 to 0.9 V:
Vehicle driven at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
Short FT #1
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to 20%
This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric level.
Long FT #1
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-15 to 15%
This item refers to the overall fuel compensation carried out in the long-term to compensate a continual deviation of the short-term fuel trim from the central value.
Total FT #1*3
Total fuel trim of bank 1
Average value for fuel trim system of bank 1/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2
-
Fuel System Status #1
Fuel system status (bank 1)/
OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up
  1. OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (bank 2)/
OL, CL, OLDrive, OLFault or CLFault
Unused
-
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
BTDC 5 to 15 deg.: Idling
-
Knock Feedback Value
Feedback value of knocking/
Min.: -1024 CA, Max.: 1023.9 CA
-20 to 0 CA:
Vehicle driven at 70 km/h (44 mph)
Service data
Knock Correct Learn Value
Correction learned value of knocking/
Min.: -1024 CA, Max.: 1023.9 CA
0 to 20 CA:
Vehicle driven at 70 km/h (44 mph)
Service data
VVT Control Status #1*2
Variable valve timing (VVT) control status (bank 1)/
ON or OFF
-
The Active Test support data
VVT Aim Angle #1*2
VVT aim angle (bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%
VVT duty signal value during forced operation
VVT Change Angle #1*2
VVT change angle (bank 1)/
Min.: 0 DegFR, Max.: 639.9 DegFR
0 to 55 DegFR: Idling
Displacement angle during forced operation
VVT OCV Duty #1*2
VVT camshaft timing oil control valve operation duty (bank 1)/
Min.: 0%, Max.: 399.9%
0 to 100%
Requested duty value for forced operation
Catalyst Temp B1S1*3
Catalyst temperature (for bank 1 sensor 1)/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
-
-
Catalyst Temp B1S2*3
Catalyst temperature (for bank 1 sensor 2)/
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
-
-
Starter Signal
Starter signal/
ON or OFF
ON: Starter signal ON
OFF: Starter signal OFF
-
Starter Control*4
Starter switch signal/
ON or OFF
ON: Cranking
-
Power Steering Signal Record
Power steering switch signal/
ON or OFF
-
-
Starter Relay*4
Starter relay/
ON or OFF
ON: Cranking
-
Power Steer. Sig. Record
Power steering switch signal (history)/
ON or OFF
-
-
ACC Relay*4
ACC CUT relay/
ON or OFF
ON: Cranking
-
Neutral Position SW Signal*5
Park/neutral position switch status/
ON or OFF
ON: Shift lever in P or N
-
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
-
A/C Signal
A/C switch status/
ON or OFF
ON: A/C ON
-
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
  1. ON: Throttle valve fully closed
  2. OFF: Throttle valve open
-
Electrical Load Signal
Electrical load signal/
ON or OFF
ON: Headlights or defogger turned ON
-
Check Mode
Check mode/
ON or OFF
ON: Check mode ON
Refer to Check Mode Procedure (Click here).
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
Misfire Test Result*3
Check mode result for misfire monitor/
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for heated oxygen sensor (bank 1 sensor 1)/
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air fuel ratio sensor/
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor*3
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor*3
Misfire monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor*3
O2S (A/FS) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor*3
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
Catalyst Monitor*3
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor*3
Catalyst monitor/
Compl or Incmpl
-
-
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
-
The number of stored DTCs
MIL
MIL status/
ON or OFF
ON: MIL on
-
MIL ON Run Distance
MIL on run distance/
Min.: 0 Km, Max.: 65535 Km
Distance after DTC stored
-
Running Time from MIL ON
Running time from MIL on/
Min.: 0 min, Max.: 65535 min
Equivalent to running time after MIL on
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 min, Max.: 65535 min
Equivalent to time after DTCs cleared
-
Distance from DTC Cleared
Distance after DTC cleared/
Min.: 0 km, Max.: 65535 km
Equivalent to driven distance after DTCs cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared/
Min.: 0, Max.: 255
-
The number of warm-up cycles after the DTC is cleared
OBD Requirements
OBD requirement
E-OBD
-
Number of Emission DTC
Emission-related DTCs/
Min.: 0, Max.: 127
-
The number of emission-related DTCs
TC and TE1
TC and TE1 terminals of DLC3/
ON or OFF
-
-
Ignition Trig. Count*3
Ignition counter/
Min.: 0, Max.: 35535
0 to 400
-
Cylinder #1 Misfire Count*3
to
Cylinder #4 Misfire Count*3
Misfire counter of cylinder 1 to 4/
Min.: 0, Max.: 255
0 to 16
-
All Cylinders Misfire Count*3
All cylinders misfire counter/
Min.: 0, Max.: 255
0 to 16
-
Misfire RPM*3
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0
-
Misfire Load*3
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: Misfire 0
-
Electric Fan Motor
Electric fan motor status/
ON or OFF
ON: Electric fan motor operating
-
Idle Fuel Cut
Fuel cut idle/
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut is "ON" when the throttle valve is fully closed and the engine speed is more than 1700 rpm.
FC TAU
Fuel cut TAU: Fuel cut during very light load/
ON or OFF
ON: Fuel cut operating
The fuel cut being performed under a very light load to prevent incomplete engine combustion.
Model Code
Model code
-
Identifies model code:
ACV40
Engine Type
Engine type
-
Identifies engine type:
2AZFE
Cylinder Number
Number of cylinders/
Min.: 0, Max.: 255
-
Identifies number of cylinders:
4
Transmission Type
Transmission type
-
Identifies transmission type:
M/T or ECT (5AT)
Destination
Destination
-
Identifies destination:
Q or V
Model Year
Model year/
Min.: 1900, Max.: 2155
-
Identifies model year:
200#
System Identification
System identification
-
Identifies engine system:
Gasoline (gasoline engine)
Engine Speed of Cyl #1
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
51199 rpm: Active Test not performed
Engine Speed of Cyl #2
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
51199 rpm: Active Test not performed
Engine Speed of Cyl #3
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
51199 rpm: Active Test not performed
Engine Speed of Cyl #4
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
51199 rpm: Active Test not performed
Av Engine Speed of All Cyl
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
51199 rpm: Active Test not performed

HINT:
  1. *1: Excluding throttle valve opening percentage due to idle speed control.
  2. *2: Data List values are only displayed when performing the following Active Test: Control the VVT System (Bank 1), Control the VVT Linear (Bank 1). For other Active Test, the Data List value will be 0.
  3. *3: for European spec only
  4. *4: with smart entry and start system
  5. *5: for automatic transaxle models


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

Tester Display
Test Part
Control Range
Diagnostic Note
Control the Injection Volume
Change injection volume
Between -12.5 to 24.8%
  1. All the injectors are tested at the same time.
  2. Perform the test at less than 3000 rpm.
  3. The injection volume can be changed in 0.1 or 0.2% graduations within the control range.
Control the Injection Volume for A/F Sensor
Change injection volume
Lower by -12.5% or increase by 25%
  1. Perform the test at less than 3000 rpm.
  2. Control the Injection Volume for A/F Sensor enables the checking and graphing of the air fuel ratio sensor and heated oxygen sensor voltage outputs.
  3. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / AFS Voltage B1S1 and O2S B1S2.
Activate the VSV for Evap Control
Activate purge VSV control
ON/OFF
  1. ON: Purge VSV on.
  2. OFF: Purge VSV off.
Control the Fuel Pump / Speed
Activate fuel pump (C/OPN relay)
ON/OFF
The test is possible when the following conditions are met:
  1. The ignition switch on (IG).
  2. The engine is stopped.
Connect the TC and TE1
Turn on and off TC and CG (TE1) connection
ON/OFF
  1. ON: TC and TE1 are connected.
  2. OFF: TC and TE1 are disconnected.
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
-
Control the Electric Cooling Fan
Control electric cooling fan motor
ON/OFF
-
Activate the Starter Relay
Activate the starter relay
ON/OFF
Engine is stopped.
Activate the ACC CUT Relay
Activate the ACC CUT relay
ON/OFF
Engine is stopped.
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
The test is possible when the following conditions are met:
  1. The ignition switch on (IG).
  2. The engine is stopped.
  3. The accelerator pedal is fully depressed (Accelerator pedal position: 59 degrees or more).
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Control the VVT Linear (Bank1)
Control VVT (bank 1)
-128 to 127%
This value added to present OCV control duty
100%: Maximum advance
-100%: Maximum retard
  1. The engine stalls or idles roughly when the camshaft timing gear is operated at 100%.
  2. The test is possible during idle.
Control the VVT System (Bank1)
Control VVT (bank 1)
ON/OFF
  1. The engine stalls or idles roughly when the camshaft timing oil control valve is turned on.
  2. The engine is running and idles normally when the camshaft timing oil control valve is off.
  3. The test is possible during idle.
Control the Cylinder #1 Fuel Cut
Cylinder #1 injector fuel cut
ON/OFF
The test is possible while the vehicle is stopped and the engine is idling.
Control the Cylinder #2 Fuel Cut
Cylinder #2 injector fuel cut
ON/OFF
Control the Cylinder #3 Fuel Cut
Cylinder #3 injector fuel cut
ON/OFF
Control the Cylinder #4 Fuel Cut
Cylinder #4 injector fuel cut
ON/OFF
Control the All Cylinder Fuel Cut
All cylinder fuel cut
ON/OFF
Check the Cylinder Compression *
Check the cylinder compression pressure
(measuring engine speed for each cylinder)
ON/OFF
Fuel injection and ignition stop in all the cylinders.

HINT:
*: When performing the Active Test item "Check the Cylinder Compression" and then cranking the engine, the ECM stops the fuel injection and ignition, and measures the engine speed for each cylinder.
If the speed of one cylinder is higher than the others, the compression pressure of that cylinder can be concluded to be less than the others.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch on (IG).
  5. Turn the tester on.
  6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed of Cyl #1 to #4 and Av Engine Speed of All Cyl.

  7. While the engine is not running, press the RIGHT or LEFT button to change the Check the Cylinder Compression to ON.

    HINT:
    After performing the above procedure, the Check the Cylinder Compression Active Test will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine speed measurement will enter standby mode.

  8. Fully open the throttle.
  9. Crank the engine for about 10 seconds.
  10. Monitor the engine speed (Engine Speed of Cyl #1 to #4, Av Engine Speed of All Cyl) displayed on the tester.

    HINT:
    At first, the intelligent tester display will show each cylinder's engine speed measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine speed measurement will change to the actual engine speed.

    NOTICE:
    1. After the Check the Cylinder Compression Active Test is turned ON, it will automatically turn OFF after 255 seconds.
    2. When the Check the Cylinder Compression Active Test is OFF and the engine is cranked, the engine will start.
    3. If the Check the Cylinder Compression Active Test needs to be performed after it is turned ON and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression Active Test again.
    4. Use a fully-charged battery.

← DATA LIST / ACTIVE TEST (Jun 2006 – May 2009)DIAGNOSTIC TROUBLE CODE CHART (Jun 2006 – Sep 2006) →