2006-2011 Camry Aurion · Service Manual ENGINE

P0110 Intake Air Temperature Circuit Malfunction

Diagnostic trouble codes · Vehicles built Jun 2006 – May 2009

Also covers:

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

A132329E01
  1. The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT becomes low, the resistance of the thermistor increases. When the temperature becomes high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
  2. The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, the voltage at terminal THA varies accordingly. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

    HINT:
    When any of DTCs P0110, P0112 and P0113 are set, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.

DTC No.
Proceed to
DTC Detection Condition
Trouble Area
P0110
Step 1
Open or short in IAT sensor circuit for 0.5 seconds
(1-trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0112
Step 4
Short in IAT sensor circuit for 0.5 seconds
(1-trip detection logic)
  1. Short in IAT sensor circuit
  1. IAT sensor (built into MAF meter)
  1. ECM
P0113
Step 2
Open in IAT sensor circuit for 0.5 seconds
(1-trip detection logic)
  1. Open in IAT sensor circuit
  1. IAT sensor (built into MAF meter)
  1. ECM

HINT:
When any of these DTCs are set, check the IAT by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit


WIRING DIAGRAM

A072925E35

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    Same as actual Intake Air Temperature (IAT).

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual IAT
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    1. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A127961E02
    Disconnect the C2 Mass Air Flow (MAF) meter connector.

  1. Connect terminals THA and E2 of the MAF meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F) or higher

  1. Reconnect the MAF meter connector.



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A127959E11
    Disconnect the C2 MAF meter connector.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    THA (C2-1) - THA (C24-65)
    Below 1 Ω
    E2 (C2-2) - ETHA (C24-88)

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A084869E25
    Disconnect the C2 MAF meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the MAF meter connector.



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER

5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A127959E12
    Disconnect the C2 MAF meter connector.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    THA (C2-1) or THA (C24-65) - Body ground
    10 kΩ or higher

  1. Reconnect the MAF meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (from Jun 2009)P0110 Intake Air Temperature Circuit Malfunction (+ P0112, P0113) (from Jun 2009) →