P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Also covers:
- P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
- Refer to DTC P0136 (Click here).
- HINT:
- Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
- When any of these DTCs are set, the ECM enters fail-safe mode. In fail-safe mode, the ECM turns off the Heated Oxygen (HO2) Sensor heater. Fail-safe mode continues until the ignition switch is turned off.
- The HO2 sensor heater circuit uses a relay on the +B side of the circuit.


- Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.
DTC No.
DTC Detection Condition
Trouble Area
P0037
Heated Oxygen (HO2) sensor heater current is less than 0.3 A
(1-trip detection logic)
- Open in HO2 sensor heater circuit
- HO2 sensor heater (sensor 2)
- Engine room J/B (EFI relay)
- ECM
P0038
Heated Oxygen (HO2) sensor heater current is more than 2 A
(1-trip detection logic)
- Short in HO2 sensor heater circuit
- HO2 sensor heater (sensor 2)
- Engine room J/B (EFI relay)
- ECM
- Open in HO2 sensor heater circuit
MONITOR DESCRIPTION
The sensing position of the Heated Oxygen (HO2) sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.- Heated oxygen sensor heater range check (P0037 and P0038):
The ECM monitors the current applied to the O2 sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM determines that there is an open circuit in the heater. If the current is above the threshold value, the ECM determines that there is a short circuit in the heater.
The ECM constantly monitors the current applied to the heater. If the ECM detects an open or short circuit, the ECM turns the MIL on and sets a DTC.
If a malfunction is detected, the ECM cuts off the current applied to the heater.
Example:
The ECM sets DTC P0038 when the current in the HO2 sensor heater is more than 2 A. Conversely, when the heater current is less than 0.3 A, DTC P0037 is set.
WIRING DIAGRAM
Refer to DTC P0136 (Click here).CONFIRMATION DRIVING PATTERN
These DTCs are detected when the engine idles for 110 seconds or more.INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Disconnect the C22 Heated Oxygen (HO2) sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
HT1B (1) - +B (2)
11 to 16 Ω at 20°C (68°F)
HT1B (1) - E2 (4)
10 kΩ or higher
Reconnect the HO2 sensor connector.
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR) |
Disconnect the C22 HO2 sensor connector.

Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Specified Condition
+B (C22-2) - Body ground
9 to 14 V
Reconnect the HO2 sensor connector.
|
|
||||
| NG | |
| 3. INSPECT ENGINE ROOM J/B (EFI RELAY, EFI MAIN FUSE) |
Inspect the EFI MAIN fuse.

Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI MAIN fuse.
Inspect the EFI relay.
Remove the engine room J/B from the engine room R/B.
Measure the EFI relay resistance.
- Standard resistance:
Tester Connection
Specified Condition
1E-6 - 1E-12
10 kΩ or higher
Below 1 Ω
(Apply battery voltage between terminals 1E-9 and 1E-11)
Reinstall the engine room J/B.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (HO2 SENSOR - EFI RELAY) |
Inspect the EFI No. 3 fuse.

Remove the EFI No. 3 fuse from the engine room R/B.
Measure the EFI No. 3 fuse resistance.
- Standard resistance:
- Below 1 Ω
Reinstall the EFI No. 3 fuse.
Disconnect the C22 HO2 sensor connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
+B (C22-2) - Engine room J/B (1E-6)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
+B (C22-2) or Engine room J/B (1E-6) - Body ground
10 kΩ or higher
Reconnect the HO2 sensor connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM) |
Disconnect the C22 HO2 sensor connector.

Disconnect the C24 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
HT1B (C22-1) - HT1B (C24-47)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
HT1B (C22-1) or HT1B (C24-47) - Body ground
10 kΩ or higher
Reconnect the HO2 sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 6. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 2 minutes or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
No output
A
P0037 or P0038
B
|
|
||||
| A | ||
| ||
