2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Oct 2006


CHECK CLEARANCE WARNING ECU

  1. Disconnect the O30 ECU connector.
    E102414E02

  2. Measure the voltage between each terminal of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    CLSW (O30-12) - E (O30-17)
    B - W-B
    Clearance sonar main switch signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG), clearance sonar main switch ON
    10 to 14 V
    IG (O30-15) - E (O30-17)
    R - W-B
    IG signal / IG power source signal
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    9 to 15 V
    E (O30-17) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the O30 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R1 (O30-3) - E (O30-17)
    L - W-B
    CAN communication signal
    -
    -
    R2 (O30-5) - E (O30-17)
    W - W-B
    CAN communication signal
    -
    -
    BOR (O30-7) - E (O30-17)
    V - W-B
    Rear sensor circuit power source
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    7 to 9 V
    SOF (O30-9) - E (O30-17)
    BR - W-B
    LIN communication signal (front sensor)
    -
    -
    BBZ (O30-10) - E (O30-17)
    R- W-B
    Clearance warning buzzer signal
    Buzzer not sounding
    Below 1 V
    Buzzer sounding
    Waveform 1
    EF (O30-11) - E (O30-17)
    W - W-B
    Rear sensor circuit ground
    Always
    Below 1 V
    E1 (O30-19) - E (O30-17)
    L - W-B
    Front sensor circuit ground
    Always
    Below 1 V
    E2 (O30-18) - E (O30-17)
    G - W-B
    Clearance warning buzzer ground
    Always
    Below 1 V
    BOF (O30-21) - E (O30-17)
    W - W-B
    Front sensor circuit power source
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    7 to 9 V
    SOR (O30-24) - E (O30-17)
    P - W-B
    LIN communication signal (rear sensor)
    -
    -
    If the result is not as specified, the ECU may have a malfunction.

  5. Reference:

    1. E051095E01
      Waveform 1
      Item
      Content
      Symbols
      (Terminal No.)
      BBZ (O30-10) - E (O30-17)
      Tool Setting
      2 V/DIV., 1 msec./DIV.
      Condition
      Buzzer sounding

← PROBLEM SYMPTOMS TABLE (from Jun 2009)Front Clearance Sonar Sensor Circuit (Oct 2006 – May 2009) →