TERMINALS OF ECU
System information · Vehicles built from Jun 2009
| CHECK CLEARANCE WARNING ECU |


Disconnect the O30 connector from the clearance warning ECU assembly.
Measure the voltage and check for pulses between each terminal of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
O30-1 (PL) - O30-21 (E)
BR - W-B
P shift position signal
Ignition switch on (IG), shift lever in any position except P
Below 1 V
Ignition switch on (IG), shift lever in P
11 to 14 V
O30-3 (SPD) - O30-21 (E)
V - W-B
Vehicle speed signal
Ignition switch on (IG), vehicle is stopped
Below 1 V
Ignition switch on (IG), wheel turned slowly
Pulse generation (See waveform 1)
O30-10 (IG) - O30-21 (E)
B - W-B
IG signal / IG power source signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
9 to 15 V
O30-13 (RL) - O30-21 (E)
R - W-B
R shift position signal
Ignition switch on (IG), shift lever in any position except R
Below 1 V
Ignition switch on (IG), shift lever in R
11 to 14 V
O30-21 (E) - Body ground
W-B - Body ground
ECU ground
Always
Below 1 V
Reconnect the O30 connector to the clearance warning ECU assembly.
Measure the voltage and check for pulses according to the value(s) in the table below.
If the result is not as specified, the ECU may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
O30-6 (SOR) - O30-21 (E)
P - W-B
Back sonar sensor communication signal (LIN communication signal)
Ignition switch on (IG), clearance sonar main switch on, shift lever in R
Pulse generation (See waveform 2)
O30-24 (BOR) - O30-21 (E)
V - W-B
Rear sensor circuit power source
Ignition switch off
Below 1 V
Ignition switch on (IG)
7.2 to 8.8 V
O30-12 (BBZ) - O30-21 (E)
BE - W-B
Clearance warning buzzer signal
Buzzer not sounding
Below 1 V
Buzzer sounding
Pulse generation (See waveform 3)
O30-22 (E2) - O30-21 (E)
G - W-B
Rear sensor circuit ground
Always
Below 1 V
Using oscilloscope:
Waveform 1 (Reference)

Item
Content
Terminal No.
(Symbol)
O30-3 (SPD) - O30-21 (E)
Tool Setting
5 V/DIV., 20 msec./DIV.
Vehicle condition
Driving at approx. 20 km/h (12 mph)
Waveform 2 (Reference)

Item
Content
Terminal No.
(Symbol)
O30-6 (SOR) - O30-21 (E)
Tool Setting
2 V/DIV., 200 μsec./DIV.
Condition
Ignition switch on (IG), clearance sonar main switch on, shift lever in R
Waveform 3 (Reference)

Item
Content
Terminal No.
(Symbol)
O30-12 (BBZ) - O30-21 (E)
Tool Setting
2 V/DIV., 200 μsec./DIV.
Buzzer condition
Buzzer sounding