2006-2011 Camry Aurion · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


CHECK ENGINE SWITCH
B146454E01
  1. Disconnect the E52 switch connector.

  2. Measure the resistance according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E52-8) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E52 switch connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E52-8) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω
    VC5 (E52-14) - AGND (E52-8)
    R - G
    Power supply
    Key is not in cabin
    Below 1 V
    Engine switch is pressed
    4.6 to 5.4 V
    CODE (E52-10) - AGND (E52-8)
    W - G
    Demodulated signal of key code data
    Key is not in cabin
    Below 1 V
    Engine switch is pressed and key is held close to engine switch*
    Pulse generation
    (See waveform 1)
    TXCT (E52-9) - AGND (E52-8)
    GR - G
    Key code output signal
    Key is not in cabin
    Below 1 V
    Engine switch is pressed and key is held close to engine switch*
    Pulse generation
    (See waveform 2)

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the switch may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B139211E01
      Waveform 1 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      CODE (E52-10) - AGND (E52-8)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch is pressed and key is held close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    2. B139212E01
      Waveform 2 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      TXCT (E52-9) - AGND (E52-8)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch is pressed and key is held close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.


CHECK CERTIFICATION ECU
B106648E23
  1. Disconnect the E58 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E (E58-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (E58-1) - E (E58-17)
    W - W-B
    +B power supply
    Always
    10 to 14 V
    IG (E58-18) - E (E58-17)
    LG - W-B
    Ignition power supply
    Engine switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E58 ECU connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (E58-40) - Body ground
    G - Body ground
    Engine switch ground
    Always
    Below 1 Ω
    VC5 (E58-30) - AGND (E58-40)
    R - G
    Engine switch power supply
    Key is not in cabin
    Below 1 V
    Engine switch is pressed
    4.6 to 5.4 V
    CODE (E58-9) - AGND (E58-40)
    W - G
    Engine switch CODE input
    Key is not in cabin
    Below 1 V
    Engine switch is pressed and key is held close to engine switch*
    Pulse generation
    (See waveform 1)
    TXCT (E58-8) - AGND (E58-40)
    GR - G
    Engine switch TXCT output
    Key is not in cabin
    Below 1 V
    Engine switch is pressed and key is held close to engine switch*
    Pulse generation
    (See waveform 2)

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the ECU may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B139211E01
      Waveform 1 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      CODE (E58-9) - AGND (E58-40)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch is pressed and key is held close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    2. B139212E01
      Waveform 2 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      TXCT (E58-8) - AGND (E58-40)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch is pressed and key is held close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.


CHECK ID CODE BOX
B118534E03
  1. Disconnect the E50 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (E50-8) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (E50-1) - GND (E50-8)
    W - W-B
    +B power supply
    Always
    10 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E50 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    EFII (E50-5) - GND (E50-8)
    G - W-B
    ECM input signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    Pulse generation
    (See waveform 1)
    EFIO (E50-6) - GND (E50-8)
    L - W-B
    ECM output signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    Pulse generation
    (See waveform 2)
    1. If the result is not as specified, the ECU may have a malfunction.

  5. Inspect using an oscilloscope.

    1. B139209E01
      Waveform 1 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      EFII (E50-5) - GND (E50-8)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)

    2. B139210E01
      Waveform 2 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      EFIO (E50-6) - GND (E50-8)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK STEERING CONTROL ECU
B118684E03
  1. Disconnect the E51 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SGND (E51-2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND (E51-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B (E51-7) - Body ground
    P - Body ground
    +B power supply
    Always
    10 to 14 V
    IG2 (E51-6) - Body ground
    B - Body ground
    Ignition power supply
    Engine switch off
    0 V
    Engine switch on (IG)
    10 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM
B139201E05
  1. Measure the resistance and voltage according to the value(s) in the table below.

    for LHD: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (C55-81) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IMI (A55-11) - E1 (C55-81)
    Y - W-B
    Immobiliser code ECU input signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    Pulse generation
    (See waveform 1)
    IMO (A55-10) - E1 (C55-81)
    G - W-B
    Immobiliser code ECU output signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    Pulse generation
    (See waveform 2)
    for RHD: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1 (C58-81) - Body ground*1
    E1 (C24-104) - Body ground*2
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IMI (A24-11) - E1 (C58-81)*1
    IMI (A24-11) - E1 (C24-104)*2
    Y - W-B
    Immobiliser code ECU input signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    Pulse generation
    (See waveform 1)
    IMO (A24-10) - E1 (C58-81)*1
    IMO (A24-10) - E1 (C24-104)*2
    G - W-B
    Immobiliser code ECU output signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    Pulse generation
    (See waveform 2)
    1. *1: for 2GR-FE
    2. *2: for 2AZ-FE
    1. If the result is not as specified, the ECM may have a malfunction.

  2. Inspect using an oscilloscope.

    1. B139210E01
      Waveform 1 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      for LHD
      IMI (A55-11) - E1 (C55-81)
      for RHD (2GR-FE)
      IMI (A24-11) - E1 (C58-81)
      for RHD (2AZ-FE)
      IMI (A24-11) - E1 (C24-104)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)

    2. B139209E01
      Waveform 2 (Reference)
      Item
      Content
      Symbols (Terminal No.)
      for LHD
      IMO (A55-10) - E1 (C55-81)
      for RHD (2GR-FE)
      IMO (A24-10) - E1 (C58-81)
      for RHD (2AZ-FE)
      IMO (A24-10) - E1 (C24-104)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK MAIN BODY ECU (INSTRUMENT PANEL J/B)
  1. Disconnect the IF and IM junction block connectors.

  2. Disconnect the E8, E7, and E6 main body ECU (instrument panel J/B) connectors.
    B128347E01

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND1 (IF-10) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND2 (IM-9) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    GND3 (E8-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    AM1 (E7-6) - Body ground
    L - Body ground
    +B power supply
    Always
    10 to 14 V
    AM2 (E6-1) - Body ground
    L - Body ground
    +B power supply
    Always
    10 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

← TERMINALS OF ECU (Oct 2006 – May 2009)DIAGNOSIS SYSTEM (from Oct 2006) →