2006-2011 Camry Aurion · Service Manual BRAKE

BLEEDING

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

HINT:
If any work is performed on the brake system or if air in the brake lines is suspected, bleed the air from the brake system.

NOTICE:
  1. Move the shift lever to the P position and apply the parking brake before bleeding the brakes.
  2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
  3. If brake fluid leaks onto any painted surface, wash off and remove it completely.
  4. Do not operate the brake actuator while air is in the brake system or in the brake master cylinder. Doing so may cause air to enter the brake actuator.
  5. If bleeding the brake actuator is difficult due to air in the actuator, replace it with a new one.


1. FILL RESERVOIR WITH BRAKE FLUID

  1. C132849
    Fill the reservoir with brake fluid.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


2. BLEED MASTER CYLINDER

HINT:
  1. If the master cylinder is reinstalled or if the reservoir becomes empty, bleed the air from the master cylinder.
  2. To avoid brake fluid from contacting and/or damaging, cover the painted surface with a shop rag or a piece of cloth.

  1. Using SST, disconnect the 2 brake lines from the master cylinder.

    SST
    09023-00101  
    09023-38201  

    C143755E01

  1. C132848E01
    Slowly depress the brake pedal and hold it (*1).

  1. C132847E01
    Cover the 2 outer holes with fingers, and release the brake pedal (*2).

  1. Repeat (*1) and (*2) 3 or 4 times.

  1. Using SST, connect the 2 brake lines to the master cylinder.

    SST
    09023-00101  
    09023-38201  

    C143754E02

    Torque:
    Without SST without VSC:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    With SST without VSC:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }
    Without SST with VSC:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    With SST with VSC:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.


3. BLEED BRAKE LINE

NOTICE:
Bleed the air from the brake line of the wheel farthest from the master cylinder.

  1. C132853
    Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*3).

  1. C132852
    When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*4).

  1. Repeat (*3) and (*4) until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug completely.

    Torque:
    for LHD:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    for RHD:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Repeat the above procedures for each wheel to bleed the air from the brake line.


4. INSPECT FOR FLUID LEAK

HINT:
If fluid leaks, tighten or replace the leaking part.


5. INSPECT FLUID LEVEL IN RESERVOIR

  1. C144901E01
    Check the fluid level.
    If brake fluid level is low, check for leakage and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair and replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3

← BLEEDING (Jun 2006 – Sep 2006)BLEEDING (from Jun 2009) →