2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1424/24 Solar Sensor Circuit (Driver Side)

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

E107008E01
The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output voltage from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The A/C amplifier detects output voltage from the solar sensor.
DTC No.
DTC Detection Condition
Trouble Area
B1424/24
Open or short in driver side solar sensor circuit
  1. Solar sensor
  2. Harness or connector between solar sensor and A/C amplifier
  3. Harness or connector between solar sensor and main body ECU
  4. A/C amplifier
  5. Main body ECU

WIRING DIAGRAM

E109253E33

INSPECTION PROCEDURE

HINT:
  1. If DTC B1244 is output at the same time, troubleshoot DTC B1244 first (Click herefor 2AZ-FE, Click here for 2GR-FE).
  2. If the check is performed in a dark place, DTC B1421/21 or B1424/24 (solar sensor circuit abnormal) may be output even though the system is normal.


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Expose the sensing portion of the solar sensor to light.

    HINT:
    Use an incandescent light for inspection.

  1. Select the item below in the Data List, and read the display on the intelligent tester.

Data List / Air Conditioner: 
Tester Display
Measure Item/Range
Normal Condition
Diagnostic Note
Solar Sensor (D side)
(Solar Sens-D)
Driver side solar sensor / Min.: 0, Max.: 255
Driver side solar sensor value increases as brightness increases
-

OK:
The display is as specified in the normal condition column.


Result:
Result
Proceed to
NG
A
OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
B
OK (When troubleshooting according to the DTC)
C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE AIR CONDITIONING AMPLIFIER
A


2. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR)

  1. E124476E37
    Disconnect the solar sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E11-6 (CLTB) - E11-3 (CLTE) (*1, *2)
    Ignition switch off
    Below 1 V
    E11-6 (CLTB) - E11-3 (CLTE) (*1, *2)
    Ignition switch on (IG)
    10 to 14 V
    h1-6 (CLTB) - h1-3 (CLTE) (*3)
    Ignition switch off
    Below 1 V
    h1-6 (CLTB) - h1-3 (CLTE) (*3)
    Ignition switch on (IG)
    10 to 14 V

    HINT:
    1. *1: LHD with the 2GR-FE
    2. *2: RHD with the 2AZ-FE
    3. *3: RHD with the 2GR-FE



OK
Go to step 4
NG


3. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - MAIN BODY ECU)

  1. E124475E02
    Disconnect the main body ECU connector.

  1. E124476E37
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-20 (CLTB) - E11-6 (CLTB) (*1, *2)
    Always
    Below 1 Ω
    E6-18 (CLTE) - E11-3 (CLTE) (*1, *2)
    Always
    Below 1 Ω
    E6-20 (CLTB) - h1-6 (CLTB) (*3)
    Always
    Below 1 Ω
    E6-18 (CLTE) - h1-3 (CLTE) (*3)
    Always
    Below 1 Ω
    E6-20 (CLTB) - Body ground
    Always
    10 kΩ or higher
    E6-18 (CLTE) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. *1: LHD with the 2GR-FE
    2. *2: RHD with the 2AZ-FE
    3. *3: RHD with the 2GR-FE



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

4. CHECK SOLAR SENSOR

  1. E109215E39
    Remove the solar sensor with its connector still connected.

  1. Connect the positive (+) lead from the battery to terminal 6 (CLTB), and the negative (-) lead to terminal 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LHD:
    Tester Connection
    Condition
    Specified Condition
    E11-1 (TSL) - E11-3 (CLTE) (*1)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    E11-1 (TSL) - E11-3 (CLTE) (*1)
    Sensor is covered with a cloth
    Below 0.8 V
    RHD:
    Tester Connection
    Condition
    Specified Condition
    E11-2 (TSR) - E11-3 (CLTE) (*2)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    E11-2 (TSR) - E11-3 (CLTE) (*2)
    Sensor is covered with a cloth
    Below 0.8 V
    h1-2 (TSR) - h1-3 (CLTE) (*3)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    h1-2 (TSR) - h1-3 (CLTE) (*3)
    Sensor is covered with a cloth
    Below 0.8 V

    HINT:
    1. *1: LHD with the 2GR-FE
    2. *2: RHD with the 2AZ-FE
    3. *3: RHD with the 2GR-FE

    NOTICE:
    1. The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6, and the positive (+) lead to terminal 3 of the solar sensor.
    2. While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
    2. As the inspection light is moved away from the sensor, the voltage decreases.



NG
REPLACE SOLAR SENSOR
OK


5. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - A/C AMPLIFIER)

  1. E124476E38
    Disconnect the solar sensor connector.

  1. E124470E09
    Disconnect the A/C amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LHD:
    Tester Connection
    Condition
    Specified Condition
    E38-33 (TSD) - E11-1 (TSL) (*1)
    Always
    Below 1 Ω
    E38-33 (TSD) - Body ground (*1)
    Always
    10 kΩ or higher
    RHD:
    Tester Connection
    Condition
    Specified Condition
    E38-33 (TSD) - E11-2 (TSR) (*2)
    Always
    Below 1 Ω
    E38-33 (TSD) - h1-2 (TSR) (*3)
    Always
    Below 1 Ω
    E38-33 (TSD) - Body ground (*2, *3)
    Always
    10 kΩ or higher

    HINT:
    1. *1: LHD with the 2GR-FE
    2. *2: RHD with the 2AZ-FE
    3. *3: RHD with the 2GR-FE



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER


← B1424/24 Solar Sensor Circuit (Driver Side) (Jun 2006 – Sep 2006)B1424/24 Solar Sensor Circuit (Driver Side) (from Jun 2009) →