TERMINALS OF ECU
System information · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| FRONT POWER SEAT SWITCH RH (POSITION CONTROL ECU) |


Disconnect the T20 and T21 ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND (T20-1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
+B (T20-5) - GND (T20-1)
G - W-B
Power source
Always
10 to 14 V
IG (T21-4) - GND (T20-1)
B - W-B
Engine switch signal
Engine switch off
Below 1 V
Engine switch on (IG)
10 to 14 V
CANH (T21-5) - CANL (T21-1)
L - W
CAN communication line
Always
Pulse generation
SYSB (T21-8) - GND (T20-1)
W - W-B
System power source
Always
10 to 14 V
Reconnect the T20 and T21 ECU connectors.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the front power seat switch RH (position control ECU) may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
SLD+ (T20-2) - GND (T20-1)
L - W-B
Sliding motor signal (forward)
Slide switch OFF
Below 1 V
Slide switch FRONT ON
10 to 14 V
SLD- (T20-3) - GND (T20-1)
Y - W-B
Sliding motor signal (rearward)
Slide switch OFF
Below 1 V
Slide switch REAR ON
10 to 14 V
FRV+ (T20-6) - GND (T20-1)
R - W-B
Front vertical motor signal (upward)
Front vertical switch OFF
Below 1 V
Front vertical switch UP ON
10 to 14 V
FRV- (T20-4) - GND (T20-1)
B - W-B
Front vertical motor signal (downward)
Front vertical switch OFF
Below 1 V
Front vertical switch DOWN ON
10 to 14 V
LFT+ (T20-7) - GND (T20-1)
W - W-B
Lifter motor signal (upward)
Lifter switch OFF
Below 1 V
Lifter switch UP ON
10 to 14 V
LFT- (T20-9) - GND (T20-1)
V - W-B
Lifter motor signal (downward)
Lifter switch OFF
Below 1 V
Lifter switch DOWN ON
10 to 14 V
RCL+ (T20-8) - GND (T20-1)
P - W-B
Reclining motor signal (forward)
Reclining switch OFF
Below 1 V
Reclining switch FRONT ON
10 to 14 V
RCL- (T20-10) - GND (T20-1)
BR - W-B
Reclining motor signal (rearward)
Reclining switch OFF
Below 1 V
Reclining switch REAR ON
10 to 14 V
| OUTER MIRROR CONTROL ECU |


Disconnect the E85 and E86 ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
CAN (E85-1) - CGND (E85-21)
L - W
CAN communication line
Always
Pulse generation
MSWE (E85-10) - Body ground
O - Body ground
Ground for seat memory switch
Always
Below 1 Ω
GND (E86-9) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
B (E86-3) - GND (E86-9)
W-R - W-B
Battery (ECU power source)
Always
10 to 14 V
ACC (E86-4) - GND (E86-9)
B-R - W-B
Engine switch (ACC) power source supply
Engine switch off
Below 1 V
Engine switch on (ACC)
10 to 14 V
Reconnect the E85 and E86 ECU connectors.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the outer mirror control ECU may have a malfunction.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
M2 (E85-7) - MSWE (E85-10)
G - O
M2 switch signal for seat memory switch
M2 switch ON
Below 1 V
M2 switch OFF
10 to 14 V
M1 (E85-8) - MSWE (E85-10)
P - O
M1 switch signal for seat memory switch
M1 switch ON
Below 1 V
M1 switch OFF
10 to 14 V
MM (E85-9) - MSWE (E85-10)
B - O
SET switch signal for seat memory switch
SET switch ON
Below 1 V
SET switch OFF
10 to 14 V