2006-2011 Camry Aurion · Service Manual ENGINE

P0560 System Voltage

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, these memories are cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and set the DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back-up power source circuit
(1 trip detection logic)
  1. Open in back-up power source circuit
  2. ECM

HINT:
If DTC P0560 is set, the ECM does not store other DTCs.


WIRING DIAGRAM

A138979E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).


1. INSPECT FUSE (EFI NO. 1)

  1. A135030E01
    Remove the EFI No. 1 fuse from the engine room R/B.

  1. Measure the EFI No. 1 fuse resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the EFI No. 1 fuse.



NG
REPLACE EFI NO. 1 FUSE
OK


2. CHECK HARNESS AND CONNECTOR

  1. A132292E04
    Check the harness and connector between the EFI No. 1 fuse and ECM.
    1. Remove the EFI No. 1 fuse from the engine room R/B.

    2. Disconnect the A24 (RHD) or A55 (LHD) ECM connector.

    3. Measure the resistance between the terminals.

      Standard resistance (Check for open):
      RHD:
      Tester Connection
      Specified Condition
      Engine room R/B EFI No. 1 fuse terminal 2 - BATT (A24-20)
      Below 1 Ω
      LHD:
      Tester Connection
      Specified Condition
      Engine room R/B EFI No. 1 fuse terminal 2 - BATT (A55-20)
      Below 1 Ω


      Standard resistance (Check for short):
      RHD:
      Tester Connection
      Specified Condition
      Engine room R/B EFI No. 1 fuse terminal 2 or BATT (A24-20) - Body ground
      10 kΩ or higher
      LHD:
      Tester Connection
      Specified Condition
      Engine room R/B EFI No. 1 fuse terminal 2 or BATT (A55-20) - Body ground
      10 kΩ or higher

    4. Reinstall the ECM connector.

  1. Check the harness and the connector between the EFI No. 1 fuse and battery.

    1. Disconnect the negative battery terminal.

    2. Disconnect the positive battery terminal.

    3. Measure the resistance between the terminals.

      Standard resistance:
      Check for open:
      Tester Connection
      Specified Condition
      Battery positive terminal - Engine room R/B EFI No. 1 fuse terminal 1
      Below 1 Ω
      Check for short:
      Tester Connection
      Specified Condition
      Battery positive terminal or Engine room R/B EFI No. 1 fuse terminal 1 - Body ground
      10 kΩ or higher

    4. Reconnect the positive battery terminal.

    5. Disconnect the negative battery terminal.

    6. Reinstall the EFI No. 1 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


4. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


5. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Turn the intelligent tester off.

  1. Start the engine and turn the intelligent tester on.

  1. Select the following menu items: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0560
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE ECM (Click here)


← P0505 Idle Control System Malfunction (from Jun 2009)P0560 System Voltage (from Jun 2009) →