2006-2011 Camry Aurion · Service Manual ENGINE

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to ECM for 20 seconds (1-trip detection logic):
  1. (a) Vehicle speed 20 km/h (12.4 mph) or more
  2. (b) Engine speed 1,000 rpm or more
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch (Automatic transaxle)
  2. Starter relay circuit
  3. Cranking holding function circuit*1
  4. Ignition switch*2
  5. ECM
*1: With smart entry and start system
*2: Without smart entry and start system

WIRING DIAGRAM

A145164E06
A132349E01

INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine does not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the on (IG) and START positions.

    OK:
    Ignition Switch Position
    Starter Signal
    on (IG)
    OFF
    START
    ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS

2. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:
For vehicles with the manual transaxle, proceed to step 5.

  1. A107908E64
    Disconnect the C1 PNP switch connector.

  1. Measure the resistance when the transaxle gear selector lever is moved to each position.

    Standard resistance:
    Gear Selector
    Lever Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    Below 1 Ω
    N
    2 - 9, 4 - 5
    Below 1 Ω
    D
    2 - 7
    Below 1 Ω
    2
    2 - 3
    Below 1 Ω
    L
    2 - 8
    Below 1 Ω

    Result:
    Result
    Proceed to
    NG
    A
    OK (without smart entry and start system)
    B
    OK (with smart entry and start system)
    C

  1. Reconnect the PNP switch connector.



B
Go to step 5

C
Go to step 8
A


3. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NEXT


4. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the on (IG) and START positions.

    OK:
    Ignition Switch Positions
    Starter Signal
    on (IG)
    OFF
    START
    ON

    Result:
    Result
    Proceed to
    OK
    A
    NG (without smart entry and start system)
    B
    NG (with smart entry and start system)
    C



B
Go to step 5

C
Go to step 8
A

END

5. INSPECT IGNITION SWITCH ASSEMBLY

  1. A056879E35
    Disconnect the E23 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All Terminals
    LOCK
    10 kΩ or higher
    2 - 4
    ACC
    Below 1 Ω
    1 - 2 - 4, 5 - 6
    ON
    1 - 3 - 4, 5 - 6 - 7
    START

  1. Reconnect the ignition switch connector.



OK
Go to step 7
NG


6. REPLACE IGNITION SWITCH ASSEMBLY

NEXT


7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the on (IG) and START positions.

    OK:
    Ignition Switch Positions
    Starter Signal
    on (IG)
    OFF
    START
    ON



NG
Go to step 8
OK

END

8. REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY CIRCUIT)

NEXT


9. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC
    B



B
END
A

REPLACE ECM


← P0617 Starter Relay Circuit High (Oct 2006 – May 2009)P0724 Brake Switch "B" Circuit High (Jun 2006 – May 2009) →