2006-2011 Camry Aurion · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Jun 2009

Also covers:

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet.
The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
When either condition below is met:
  1. No CKP sensor signal to ECM while cranking (1-trip detection logic)
  1. No CKP sensor signal to ECM at engine speed of 600 rpm or more (1-trip detection logic)
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more
(1-trip detection logic):
(a) Engine speed 1,000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have lapsed since starter signal is switched from ON to OFF
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. CKP sensor plate
  4. ECM

  1. A063955E23
    Reference: Inspection using an oscilloscope.

    HINT:
    1. The correct waveform is as shown.
    1. G2 stands for the CMP sensor signal, and NE+ stands for the CKP sensor signal.
    2. Grounding failure of the shielded wire may cause noise in waveforms.

    Item
    Content
    Terminals
    CH1: G2+ - G2-
    CH2: NE+ - NE-
    Equipment Settings
    5 V/DIV.
    20 ms./DIV.
    Conditions
    Cranking or idling

WIRING DIAGRAM

A134999E01

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
  2. Check the engine speed. The engine speed can be checked by using the intelligent tester. Follow the procedure below:
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine.
    3. Turn the tester on.
    4. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the tester while the engine is running.

    OK:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the tester.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the tester remains zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS

2. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

  1. G037727E06
    Disconnect the C20 Crankshaft Position (CKP) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    1,150 to 1,450 Ω

  1. Reconnect the CKP sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

  1. A127716E02
    Disconnect the C20 CKP sensor connector.

  1. Disconnect the C24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    NE+ (C20-1) - NE+ (C24-122)
    Below 1 Ω
    NE- (C20-2) - NE- (C24-121)

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    NE+ (C20-1) or NE+ (C24-122) - Body ground
    10 kΩ or higher
    NE- (C20-2) or NE- (C24-121) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the CKP sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

  1. BR03795E25
    Check the CKP sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR
OK


5. CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE
OK


6. REPLACE CRANKSHAFT POSITION SENSOR

NEXT


7. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) position and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    Proceed to
    No output
    A
    P0335 or P0339
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Oct 2006 – May 2009)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (Jun 2006 – Sep 2006) →