2006-2011 Camry Aurion · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133884E01
    Install the center airbag sensor assembly with the 3 bolts.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  1. Connect the holder (with connectors).

  1. Check that the water-proof sheet is properly set.


2. INSTALL NO. 1 CONSOLE BOX DUCT

  1. C129716
    Install the No. 1 console box duct with the clip.


3. INSTALL FLOOR CARPET BRACKET LH

4. INSTALL FLOOR CARPET BRACKET RH

5. INSTALL CONSOLE BOX ASSEMBLY

  1. B158940
    Engage the 2 claws.

  1. B158939
    Install the 2 bolts <I>.

  1. B158937
    Install the 3 screws <H>.

  1. B158938
    Install the console box assembly with the 3 screws <H>.

  1. B158936E01
    Engage the clamp.


6. INSTALL CONSOLE BOX CARPET

  1. B158935
    Install the console box carpet.


7. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
  1. Connect the connector.

  1. B158962
    Engage the 10 claws and install the upper console panel sub-assembly.


8. INSTALL UPPER CONSOLE PANEL FRONT GARNISH

  1. B158963
    Connect each connector.

  1. Engage the 6 claws and install the upper console panel front garnish.


9. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B158971
    Install the shift lever knob sub-assembly.


10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B158922E01
    Engage the 3 claws and 3 clips.

  1. Install the screw <F> or <N>.

  1. Install the 3 screws <F>.

  1. Install the lower instrument panel sub-assembly with the bolt <D>.


11. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B158969E01
    Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover sub-assembly.


12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH and LH side (Click here).


13. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH and LH side (Click here).


14. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B158913E01
    Install the air hose and connect each connector.

  1. Engage the claw and the 4 clips.

  1. Engage the 2 claws and the DLC3.

  1. Install the lower No. 1 instrument panel finish panel with the screw <F> and bolt <D>.


15. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.


16. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B132067
    Engage the 7 claws and 3 clips, then install the front door scuff plate LH.


17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

18. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).

← INSTALLATION (Oct 2006 – May 2009)COMPONENTS (Oct 2006 – May 2009) →