2006-2011 Camry Aurion · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built Jun 2006 – Sep 2006


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)

  1. B148446
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

  1. B152779
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B152774
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144599
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


7. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B144605
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


8. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B144607E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B144602
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.


9. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)

  1. B149934
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


10. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


11. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B144604
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


12. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY

  1. B141243E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.

    HINT:
    Set the shift lever in the D position.


13. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


14. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


15. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


16. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


18. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133988E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


19. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the bolt <A>.

  1. B133992E01
    Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.


20. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.


21. REMOVE CONSOLE BOX CARPET

  1. B134004
    Remove the console box carpet.


22. REMOVE CONSOLE BOX ASSEMBLY

  1. B134002E01
    Remove the 2 screws <F>.

  1. B149935E03
    Disengage the clamp.

  1. Remove the 2 bolts <G> and the console box assembly.


23. REMOVE NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.


24. REMOVE NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.


25. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)

  1. C129716
    Remove the clip and No. 1 console box duct.


26. REMOVE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn back the carpet.

  1. C133884
    Disconnect the holder (with connectors).

  1. Remove the 3 bolts and center airbag sensor assembly.

← ON-VEHICLE INSPECTION (Jun 2006 – Sep 2006)INSTALLATION (Jun 2006 – Sep 2006) →