2006-2011 Camry Aurion · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


4. REMOVE NO. 3 LOWER STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.

    C146012E01

    HINT:
    Tape up the screwdriver tip before use.


5. REMOVE NO. 2 LOWER STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.

    C146013E01

    HINT:
    Tape up the screwdriver tip before use.


6. REMOVE STEERING PAD

  1. Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    C146014E01

  1. C133859E01
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector from the steering pad.

  1. Disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C145839E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


8. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


11. REMOVE STEERING COLUMN COVER

  1. B137294E01
    Remove the 2 screws <D>.

  1. Disengage the 2 claws and remove the lower steering column cover.

  1. Disengage the claw and remove the upper steering column cover.


12. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C145843
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


13. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

  1. B149938
    Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the No. 1 instrument panel sub-assembly.


14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Smart Entry and Start System)

  1. B144612
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.


15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Smart Entry and Start System)

  1. B159330
    Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.

  1. Disconnect the connector.


16. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B133985E01
    Remove the 2 clips.

  1. Disengage the guide and 4 claws, and then remove the instrument cluster finish panel sub-assembly.


17. REMOVE COMBINATION METER ASSEMBLY

  1. B152781E01
    Remove the 4 screws <E>.

  1. Disconnect each connector and remove the combination meter assembly.


18. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


20. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY

  1. B133988E01
    Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.


21. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B133992E01
    Remove the bolt <A>.

  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.


22. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B226062
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


23. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B232854
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


24. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)

  1. B232855
    Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.


25. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B226063
    Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.


26. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. B226064
    Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.


27. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle LHD)

  1. B226065
    Disengage the 6 claws and the 3 clips, and then remove the position indicator housing assembly.


28. REMOVE POSITION INDICATOR HOUSING ASSEMBLY (for Automatic Transaxle RHD)

  1. B232856E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B232857
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the position indicator housing assembly as shown in the illustration.


29. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)

  1. B137274E01
    Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.

  1. B137275
    Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.


30. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle LHD)

  1. B226097
    Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.


31. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle RHD)

  1. B137277
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


32. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)

  1. B137277
    Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.


33. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B133997E01
    Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.


34. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY

  1. B152782E01
    Apply protective tape to the areas shown in the illustration.

  1. B152783
    Using a moulding remover, disengage the 3 clips.

  1. B152784
    Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.


35. REMOVE RADIO AND CASSETTE TAPE WITH HEATER CONTROL PANEL ASSEMBLY (w/o CD Player)

  1. E135568
    Remove the 4 bolts.

  1. Pull the radio and cassette tape with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio and cassette tape with heater control panel assembly.


36. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (for Radio Receiver Type)

  1. E129175
    Remove the 4 bolts.

  1. Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver with heater control panel assembly.


37. REMOVE RADIO AND DISPLAY WITH HEATER CONTROL PANEL ASSEMBLY (for Radio and Display Type)

  1. E195855
    Remove the 4 bolts.

  1. Pull the radio and display with heater control panel assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio and display with heater control panel assembly.


38. REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)

  1. E137564
    Remove the 4 bolts.

  1. Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver with heater control panel assembly.


39. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.


40. REMOVE CONSOLE BOX CARPET

  1. B134004
    Remove the console box carpet.


41. REMOVE CONSOLE BOX ASSEMBLY

  1. B134002E01
    Remove the 2 screws <F>.

  1. B149935E03
    Disengage the clamp.

  1. Remove the 2 bolts <G> and the console box assembly.


42. REMOVE NO. 2 CONSOLE BOX INSERT FRONT

  1. B134005E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.


43. REMOVE NO. 1 CONSOLE BOX INSERT FRONT

  1. B134006E01
    Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.


44. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.


45. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

  1. B132056E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.

  1. B132100E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


46. REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY

  1. B134007
    Disengage the 4 clips and remove the instrument panel No. 1 register assembly.


47. REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY

  1. B134009E01
    Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.


48. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH (for 6 Speakers)

  1. E129167
    Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.


49. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.


50. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

  1. B132055E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.

  1. B132099E02
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


51. REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY

  1. B134008
    Disengage the 4 clips and remove the instrument panel No. 3 register assembly.


52. REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY

  1. B134010E01
    Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.


53. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH (for 6 Speakers)

HINT:
Use the same procedure for the RH and LH side (Click here).


54. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH

  1. B134011E01
    Disengage the 8 clips and the 4 guides.

  1. Disconnect each connector and remove the No. 1 defroster nozzle garnish.


55. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C132564E01
    Disconnect the connector (yellow colored one).


56. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disengage each clamp.

  1. Disconnect each connector.

  1. Remove the bolt <J>.

  1. Remove the 2 passenger airbag bolts <C>.

    B134013E01

  1. Remove the 2 bolts <H>.

  1. Remove the 2 nuts <I>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B134014E06


57. REMOVE NO. 3 INSTRUMENT PANEL STAY

  1. Disengage the claw and remove the 5 No. 3 instrument panel stays.

    B134015


58. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY

  1. C132565
    Remove the 2 screws.

  1. C132566
    Disengage the 10 hooks and remove the front passenger airbag assembly from the instrument panel safety pad assembly.


59. REMOVE INSTRUMENT PANEL WIRE ASSEMBLY

  1. C132567E01
    Disconnect the 2 connectors.

  1. Remove the clamp and the instrument panel wire assembly from the front passenger airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Oct 2006 – May 2009) →