2006-2011 Camry Aurion · Service Manual BODY

Sliding Roof Control Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2006

DESCRIPTION

The sliding roof drive gear sub-assembly (sliding roof control ECU) receives slide switch and tilt switch signals and drives its built-in motor.

WIRING DIAGRAM

B131103E05

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDING ROOF OPERATION)
  1. Select the ACTIVE TEST, use the intelligent tester to generate a control command, and then check that the sliding roof slides open/close and tilts up/down.

    SLIDE ROOF:
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    (Slide Roof)
    Operate sliding roof SLIDE CLOSE/TILT UP
    CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs.
    OFF: Sliding roof is not operating
    -
    Slide Roof
    (Slide Roof)
    Operate sliding roof SLIDE OPEN/TILT DOWN
    OPN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs
    OFF: Sliding roof is not operating
    -
    OK:
    Sliding roof operates normally.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
OK


2. READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF SWITCH)
  1. Use the DATA LIST to check if the sliding roof switch is functioning properly.

    SLIDE ROOF:
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open SW
    (Open Switch)
    Slide switch open signal/ON or OFF
    ON: OPEN switch is pressed.
    OFF: OPEN switch is not pressed.
    -
    Close SW
    (Close Switch)
    Slide switch close signal/ON or OFF
    ON: CLOSE switch is pressed.
    OFF: CLOSE switch is not pressed.
    -
    Up SW
    (Up Switch)
    Tilt switch up signal/ON or OFF
    ON: UP switch is pressed.
    OFF: UP switch is not pressed.
    -
    Down SW
    (Down Switch)
    Tilt switch down signal/ON or OFF
    ON: DOWN switch is pressed.
    OFF: DOWN switch is not pressed.
    -
    OK:
    The intelligent tester displays as shown in the table according to the operation of each switch.



OK
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF CONTROL ECU)
NG


3. CHECK WIRE HARNESS (SLIDING ROOF CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)

  1. B131169E03
    Disconnect the Q12 and Q6 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q12-2 (E) - Q6-3 (GND)
    Always
    Below 1 Ω
    Q12-7 (OPN) - Q6-2 (OPN)
    Always
    Below 1 Ω
    Q12-8 (DWN) - Q6-4 (DOWN)
    Always
    Below 1 Ω
    Q12-9 (CLS) - Q6-1 (CLS)
    Always
    Below 1 Ω
    Q12-10 (UP) - Q6-5 (UP)
    Always
    Below 1 Ω
    Q6-1 (CLS) - Body ground
    Always
    10 kΩ or higher
    Q6-2 (OPN) - Body ground
    Always
    10 kΩ or higher
    Q6-3 (GND) - Body ground
    Always
    Below 1 Ω
    Q6-4 (DOWN) - Body ground
    Always
    10 kΩ or higher
    Q6-5 (UP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ROOF CONSOLE BOX ASSEMBLY (SLIDING ROOF CONTROL SWITCH)


← B2343 Position Initialization Incomplete (from Oct 2006)Sliding Roof ECU Power Source Circuit (Jun 2006 – Sep 2006) →