DISASSEMBLY
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
- CAUTION:
- Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.
| 1.
REMOVE RECLINING POWER SEAT SWITCH KNOB |
 |
- Using a screwdriver, detach the reclining power seat switch knob.
- HINT:
- Tape the screwdriver tip before use.
| 2.
REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
 |
- Using a screwdriver, detach the slide and vertical power seat switch knob.
- HINT:
- Tape the screwdriver tip before use.
| 3.
REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY |
 |
- Disconnect the 2 hooks.
- Remove the 5 screws.
Disengage the 2 claws and separate the front seat cushion shield assembly.
Disconnect the connector from the front power seat lumbar switch.
| 4.
REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD |
 |
- Remove the screw.
Detach the 2 claws and remove the front inner No. 1 seat cushion shield.
| 5.
REMOVE FRONT POWER SEAT LUMBAR SWITCH |
 |
- Remove the 2 screws and front power seat lumbar switch.
| 6.
REMOVE FRONT SEAT INNER BELT ASSEMBLY
|
 |
- for LHD:
Disengage the 2 hooks.
- Disconnect the connectors and disengage each clamp.
Disconnect the connector.
- Remove the nut and front seat inner belt assembly.
- for RHD:
Disengage the 2 hooks.
- Disconnect the connector and disengage the 3 clamps. (for Driver seat)
Disconnect the connector. (for Driver seat)
Remove the nut and front seat inner belt assembly.


| 7.
REMOVE FRONT INNER SEAT CUSHION SHIELD |
 |
- Remove the screw.
Disengage the 3 claws and remove the front inner seat cushion shield.
| 8.
REMOVE POWER SEAT SWITCH |
 |
- Remove the 3 screws.
Disconnect the connector and remove the front power seat switch.
| 9.
REMOVE FRONT SEAT CUSHION ASSEMBLY |
 |
- Disconnect the connector.
Remove the 4 hooks.
- Using a screwdriver, detach the hooks and remove the front seat cushion assembly.
| 10.
REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER |
 |
- Remove the 16 hog rings and front separate type seat cushion cover from the seat cushion pad.
| 11.
REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY |
 |
- Remove the 2 screws.
Disconnect the 14 clamps and front separate type seatback cover.
Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.
| 12.
REMOVE FRONT SEAT HEADREST SUPPORT |
 |
- Detach the 2 claws and remove the headrest support.
- HINT:
- Use the same procedure for the RH side and LH side.
| 13.
REMOVE FRONT SEATBACK ASSEMBLY (w/o Airbag System) |
 |
- Remove the 2 hog rings and 3 hooks.
Remove the front seatback assembly.
| 14.
REMOVE FRONT SEATBACK ASSEMBLY (w/ Airbag System) |
 |
- Remove the 2 hog rings and 3 hooks.
- Remove the nut and 2 seatback cover brackets.
Remove the front seatback assembly.
| 15.
REMOVE FRONT SEPARATE TYPE SEATBACK COVER |
 |
- Remove the 10 hog rings and front separate type seatback cover from the seatback pad.
| 16.
REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY |
 |
- Disconnect the connector.
Remove the 2 screws and lumbar support adjuster assembly.
| 17.
REMOVE RECLINING ADJUSTER INSIDE COVER RH |
 |
Disconnect the harness.
- Remove the screw and lower reclining adjuster inside cover RH.
| 18.
REMOVE RECLINING ADJUSTER INSIDE COVER LH |
 |
Disconnect the harness.
- Remove the screw and reclining adjuster inside cover LH.
| 19.
REMOVE SEAT RECLINING ADJUSTER INSIDE COVER RH |
 |
- Remove the screw.
Detach the claw and remove the seat reclining adjuster inside cover RH.
| 20.
REMOVE SEAT RECLINING ADJUSTER INSIDE COVER LH |
 |
- Remove the screw.
Detach the claw and remove the seat reclining adjuster inside cover LH.
| 21.
REMOVE FRONT LOWER SEAT CUSHION SHIELD LH |
 |
- Remove the screw and detach the hook of the front lower seat cushion shield LH.
| 22.
REMOVE FRONT LOWER SEAT CUSHION SHIELD |
 |
- Remove the screw and detach the hook of the front lower seat cushion shield RH.
| 23.
REMOVE FRONT SEPARATE TYPE SEATBACK SPRING ASSEMBLY |
 |
- Disconnect the connector and detach the 3 clamps.
- Remove the 4 bolts and front separate type seatback spring assembly.
| 24.
REMOVE SEAT POSITION SENSOR (for Driver Side)
|
 |
- Disconnect the connector.
Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.
- Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.
| 25.
REMOVE FRONT SEAT WIRE |
 |
Detach the each clamp and each claw and remove the front seat wire.