2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


GENERAL
  1. This system uses ultrasonic sensors to detect any obstacles at the corners of the vehicle. The system then informs the driver of the distance between the sensors and the obstacles as well as their positions by indicating them on the multi-information display and by sounding a buzzer.


FUNCTION OF COMPONENTS
Component
Function
Ultrasonic sensor (4)
Detects the distance between the vehicle and the obstacle
Clearance warning buzzer
Sounds the buzzer to inform the driver according to the distance to the obstacle
Multi-information display on the combination meter
Transmits the vehicle speed signal to the clearance warning ECU.
  1. Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.
  2. Informs the driver if the ultrasonic sensors malfunction, or if they are frozen or dirty
Clearance sonar main switch
Operating this switch allows the operation of intuitive parking assist to be enabled or disabled.
Clearance warning ECU
Judges the approximate distance between the vehicle and the obstacle based on the signals from the ultrasonic sensors and sends it to the multi-information display.
Sounds the clearance warning buzzer
ECM
Transmits the shift position signal to the clearance warning ECU
A/C amplifier
Transmits the ambient temperature display signal to the clearance warning ECU

OPERATION EXPLANATION
  1. The operating conditions of each ultrasonic sensor differ according to its installed position as shown in the table below:

    Installation Position
    Operating Condition
    Front Corner Sensor
    1. Ignition switch is on (IG).
    2. Clearance sonar main switch is ON.
    3. Shift position is not P.
    4. Shift position is not R.
    5. Vehicle speed is approx. 10 km/h (6.2 mph) or less. The sensor stops operating when the vehicle speed exceeds 15 km/h (9.3 mph), and starts operating when the vehicle speed drops to below 10 km/h (6.2 mph).
    Rear Corner Sensor
    1. Ignition switch is on (IG).
    2. Clearance sonar main switch is ON.
    3. Shift position is R.


ECU AND SENSORS WHICH COMMUNICATE THROUGH LIN COMMUNICATION

HINT:
  1. The clearance warning ECU and sensors communicate with each other using LIN communication.
  2. Allocation refers to the process of the clearance warning ECU setting aside IDs for the sensors.
  3. The vehicle has the sensors arranged in two groups. There is a front series and a rear series. The sensors are connected in a "daisy chain".

  1. Initialization mode:
    An ID is allocated to each sensor and sensor diagnosis is performed.
    B157377E01

    1. When any of the following conditions are met, the clearance warning ECU provides power to the first sensors in each series (front left sensor and rear right sensor):

      1. The ignition switch is turned on (IG).
      2. The sensor operating conditions (described previously) are met and the clearance sonar main switch is turned on.
      3. Vehicle speed is below 10 km/h (6.2 mph).

    2. After the power is supplied, the front left sensor and rear right sensor enter standby mode to receive an ID from the ECU. When a certain amount of time has elapsed, the ECU sends an ID allocation signal to these sensors.

    3. The front left sensor and rear right sensors receive the ID allocation signal from the ECU and perform self-diagnosis. When the sensor self-diagnosis is complete, the ECU sends an ID allocation confirmation signal to the sensors.

    4. After the ID allocation confirmation is performed, the ECU provides power to the second sensors in each series (front right sensor and rear left sensor) via the first sensors. In the same manner as the first sensors, the second sensors enter the standby mode. When a certain amount of time has elapsed, the ECU sends an ID allocation signal to the second sensors. Initialization ends when 10 allocation to all ultrasonic sensors is complete.

  2. Detection mode:
    After the initialization mode is complete, the system switches into the detection mode. In the detection mode, the clearance warning ECU sends information request signals and sensor activation signals to the ultrasonic sensors and receives detection result signals from the sensors.

    1. The clearance warning ECU regularly sends ID signals, information request signals, and sensor activation signals to an ultrasonic sensor according to the LIN communication schedule.

    2. When a certain amount of time has elapsed (sensor detection operation is complete), the clearance warning ECU sends an ID signal to the sensor to receive a detection result signal.

    3. The ultrasonic sensor sends a detection result signal or detection information signal to the ECU.

    4. The above operation is repeatedly performed for each ultrasonic sensor.

← SYSTEM DESCRIPTION (Oct 2006 – May 2009)HOW TO PROCEED WITH TROUBLESHOOTING (Oct 2006 – May 2009) →