2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

OPERATION CHECK

Troubleshooting · Vehicles built from Oct 2006


SELF-CHECK FUNCTION INSPECTION
E107404E04
  1. Turn the ignition switch on (IG).

    HINT:
    Wait 2 seconds after turning the ignition switch on (IG).

  2. When the clearance sonar system is turned on, check that the following occurs: 1) after 0.4 milliseconds, the buzzer sounds for approximately 1 +/- 0.3 seconds, and 2) the system starts the obstacle detection operation.

    HINT:
    1. If a sensor has an open circuit or a sensor's detection operation malfunctions because it is wet or frozen, a malfunction display is shown in the multi-information display, and the buzzer sounds.
    2. When the sensor condition returns to normal, the system ends normal clearance sonar mode.
    3. If the ignition switch is turned on (IG) after the clearance sonar main switch is turned on, the buzzer does not sound.


MALFUNCTION DISPLAY (MULTI-INFORMATION DISPLAY)

  1. Ultrasonic sensor open circuit

    1. If there is an open circuit between the ultrasonic sensor and the clearance warning ECU or if a sensor is malfunctioning, the malfunction is displayed as shown in the illustration.
      B157384E02

      HINT:
      1. The example shows an open circuit in the ultrasonic sensor (front left sensor).
      2. If a sensor has an open circuit, a warning message will be displayed. In such a case, perform inspection according to the Problem Symptoms Table.

  2. Ultrasonic sensor frozen

    1. If a sensor is covered with foreign matter, such as mud or snow, the affected sensor is displayed as shown in the illustration.
      B157385E02

      HINT:
      1. The example shows that the ultrasonic sensor (front left sensor) is covered with foreign matter.
      2. If a message indicating the necessity of cleaning a sonar sensor is displayed, removing the foreign matter from the sensor will return the sensor to normal.


DETECTION RANGE MEASUREMENT AND DISPLAY INSPECTION
  1. Detection range measurement

    NOTICE:
    Make sure that the parking brake is firmly applied to prevent the vehicle from moving.


    1. Turn the ignition switch on (IG).

    2. Move the shift lever to the reverse position to check the ultrasonic sensors (rear sensors).

  2. Turn the clearance sonar main switch on.

  3. Move a φ 60 mm (2.36 in.) pole near each sensor to measure its detection range.

    1. Measure the clearance sonar's detection range.
      B139323E01

      NOTICE:
      These detection ranges are applicable when positioning the φ 60 mm (2.36 in.) pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle (such as walls).

    2. Measure the back sonar's detection range.
      B139322E01

      NOTICE:
      These detection ranges are applicable when positioning the φ 60 mm (2.36 in.) pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle (such as walls).

  4. When the ultrasonic sensors (front clearance sonar) have detected an obstacle, check the display and buzzer sound.

    Operation condition: 
    Ignition Switch
    Clearance Sonar Main Switch
    Shift Lever Position
    Vehicle Speed
    ON (IG)
    ON
    In any position except P
    10 km/h (6 mph) or less

    1. Check the buzzer sound according to the waveform shown in the illustration.
      E124674E06

      Standard:
      Detection Range
      Condition
      *1
      Close-range detection
      Within approx. 250 +/- 30 mm (9.84 +/- 1.18 in.)
      Buzzer: Sounds continuously
      Number of bars displayed: 1 (Blinking)
      *2
      Medium-range detection
      From approx. 250 +/- 30 to 375 +/- 40 mm (9.84 +/- 1.18 to 14.76 +/- 1.57 in.)
      Buzzer: Sounds intermittently (ON: 75 ms / OFF: 75 ms)
      Number of bars displayed: 2 (illuminated)
      *3
      Long-range detection
      From approx. 375 +/- 40 to 500 +/- 50 mm (14.76 +/- 1.57 to 19.69 +/- 1.97 in.)
      Buzzer: Sounds intermittently (ON: 150 ms / OFF: 150 ms)
      Number of bars displayed: 3 (illuminated)

      HINT:
      1. Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.
      2. Refer to the illustration of the display below.

    2. B139328E01
      Check the display according to the illustration on the left while the buzzer is sounding.

  5. When the ultrasonic sensors (back sonar) have detected an obstacle, check the display and buzzer sound.

    Operation condition: 
    Ignition Switch
    Clearance Sonar Main Switch
    Shift Lever Position
    ON (IG)
    ON
    Reverse Position

    1. Check the buzzer sound according to the waveform shown in the illustration.
      E124676E09

      Standard:
      Detection Range
      Condition
      *1
      Close-range detection
      Within approx. 350 +/- 40 mm (13.78 +/- 1.57 in.)
      Buzzer: Sounds continuously
      Number of bars displayed: 1 (blinking)
      *2
      Medium-range detection
      From approx. 350 +/- 40 to 450 +/- 50 mm (13.78 +/- 1.57 to 17.72 +/- 1.97 in.)
      Buzzer: Sounds intermittently (ON: 75 ms / OFF: 75 ms)
      Number of bars displayed: 2 (illuminated)
      *3
      Long-range detection
      From approx. 450 +/- 50 to 600 +/- 60 mm (17.72 +/- 1.97 to 23.62 +/- 2.36 in.)
      Buzzer: Sounds intermittently (ON: 150 ms / OFF: 150 ms)
      Number of bars displayed: 3 (illuminated)
      *4
      Maximum long-range detection
      From approx. 600 +/- 60 to 1,500 +/-150 mm (23.62 +/- 2.36 to 59.06 +/- 5.91 in.)
      Buzzer: Sounds intermittently (ON: 150 ms / OFF: 650 ms)
      Number of bars displayed: 4 (illuminated)

      HINT:
      1. Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.
      2. Refer to the illustration of the display below.

    2. B139327E01
      Check the display according to the illustration on the left while the buzzer is sounding.

  6. When the ultrasonic sensors (rear clearance sonar) have detected an obstacle, check the display and buzzer sound.

    Operation condition: 
    Ignition Switch
    Clearance Sonar Main Switch
    Shift Lever Position
    ON (IG)
    ON
    Reverse Position

    1. Check the buzzer sound according to the waveform shown in the illustration.
      E124674E07

      Standard:
      Detection Range
      Condition
      *1
      Close-range detection
      Within approx. 250 +/- 30 mm (9.84 +/- 1.18 in.)
      Buzzer: Sounds continuously
      Number of bars displayed: 1 (Blinking)
      *2
      Medium-range detection
      From approx. 250 +/- 30 to 375 +/- 40 mm (9.84 +/- 1.18 to 14.76 +/- 1.57 in.)
      Buzzer: Sounds intermittently (ON: 75 ms / OFF: 75 ms)
      Number of bars displayed: 2 (illuminated)
      *3
      Long-range detection
      From approx. 375 +/- 40 to 500 +/- 50 mm (14.76 +/- 1.57 to 19.69 +/- 1.97 in.)
      Buzzer: Sounds intermittently (ON: 150 ms / OFF: 150 ms)
      Number of bars displayed: 3 (illuminated)

      HINT:
      1. Ultrasonic waves are used to measure the detection range; however, the detection range may vary depending on the ambient temperature.
      2. Refer to the illustration of the display below.

    2. B139326E01
      Check the display according to the illustration on the left while the buzzer is sounding.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Jun 2009)PROBLEM SYMPTOMS TABLE (Oct 2006 – May 2009) →