DATA LIST / ACTIVE TEST
System information · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
| DATA LIST |
- HINT:
- Using the intelligent tester Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Enter / Powertrain / ECT / Data List".
Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light Switch
Stop light switch Status/
ON or OFF
- Brake Pedal is depressed: ON
- Brake Pedal is released: OFF
-
Neutral Position SW Signal
PNP switch Status/
ON or OFF
Shift lever position is;
P and N: ON
Except P and N: OFF
When the shift lever position displayed on the Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (R Range)
PNP switch Status/
ON or OFF
Shift lever position is;
R: ON
Except R: OFF
↑
Shift SW Status (D Range)
PNP switch Status/
ON or OFF
Shift lever position is;
D and 4 : ON
Except D and 4: OFF
↑
Shift SW Status (2 Range)
PNP SW Status/
ON or OFF
Shift lever position is;
2 and L : ON
Except 2 and L: OFF
↑
Shift SW Status (L Range)
PNP SW Status/
ON or OFF
Shift lever position is;
L : ON
Except L: OFF
↑
Shift SW Status (4 or D Range)
PNP SW Status/
ON or OFF
Shift lever position is;
4 : ON
Except 4: OFF
↑
Shift SW Status (3 Range)
PNP SW Status/
ON or OFF
Shift lever position is;
3 : ON
Except 3: OFF
↑
Shift Status
Actual Gear Position/
1st, 2nd, 3rd, 4th or 5th
Shift Lever Position is; - L: 1st
- 2: 1st or 2nd
- 3: 1st, 2nd or 3rd
- 4: 1st, 2nd, 3rd or 4th
- D: 1st, 2nd, 3rd, 4th or 5th
-
Lock Up Solenoid Status
Lock Up Solenoid Status/
ON or OFF
- Lock Up: ON
- Except Lock Up: OFF
-
SLT Solenoid Status
Shift Solenoid SLT Status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
A/T Oil Temperature 1
ATF Temp. Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test;
Approx. 80°C (176°F)
- Equal to ambient temperature when cold soak
If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is opened or shorted.
SPD (NT)
Input Turbine Speed/
display: 50 r/min
- HINT:
- Lock-up ON (After warning up the engine):
Input Turbine speed (NT) equal to the engine sped.
- Lock-up OFF (Idling at N position):
Input Turbine speed (NT) nearly equal to the engine speed.
- Lock-up ON (After warning up the engine):
-
SPD (NC)
Counter Gear Speed/
display: 50 r/min
- HINT:
- 3rd when shift lever position is D position (After warming up the engine);
- Intermediate shaft speed (NC) becomes close to the engine speed.
- Intermediate shaft speed (NC) becomes close to the engine speed.
-
- Brake Pedal is depressed: ON
| ACTIVE TEST |
- HINT:
- Performing the intelligent tester Active Test allows relay, Vacuum Switching Valve (VSV), actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to shorten labor time.
- The Data List can be displayed during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Enter / Powertrain / ECT / Active Test".
Follow the instructions on the tester and perform the Active Test.
*: "Activate the Solenoid (SLT)" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (Click here) as well.Tester Display
Test Part
Control Range
Diagnostic Note
Control the shift Position
[Test Details]
Operate the shift solenoid valve and set the each shift position by yourself.
[Vehicle Condition]- IDL: ON
- Less than 50 km/h (31 mph)
- Press "→" button: Shift up
- Press "←" button: Shift down
1st / 2nd / 3rd / 4th / 5th
Possible to check the operation of the shift solenoid valves.
Activate the Lock Up
[Test Details]
Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition.
[Vehicle Condition]- Vehicle Speed: 60 km/h (37 mph) or more, and 5th gear
ON / OFF
Possible to check the DSL operation.
Activate the Solenoid (SL1)
[Test Details]
Operate the shift solenoid SL1
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON / OFF
-
Activate the Solenoid (SL2)
[Test Details]
Operate the shift solenoid SL2
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON / OFF
-
Activate the Solenoid (SL3)
[Test Details]
Operate the shift solenoid SL3
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON / OFF
-
Activate the Solenoid (S4)
[Test Details]
Operate the shift solenoid S4
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON / OFF
-
Activate the Solenoid (SR)
[Test Details]
Operate the shift solenoid SR
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON / OFF
-
Activate the Solenoid (DSL)
[Test Details]
Operate the shift solenoid DSL
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON / OFF
-
Activate the Solenoid (SLT)*
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]- Vehicle Stopped.
- IDL: ON
- HINT:
- OFF: Line pressure up (When the active test of "Activate the Solenoid (SLT)" is performed, the ECM commands the SLT solenoid to turn off).
- ON: No action (normal operation)
ON / OFF
-
- HINT:
- The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.
- IDL: ON