P0766 Shift Solenoid "D" Performance (Shift Solenoid Valve S4)
Diagnostic trouble codes · Vehicles built Jun 2006 – May 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transaxle (clutch, brake or gear etc.).
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| P0766 |
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
MONITOR DESCRIPTION
The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the ECM detects the actual gear position (1st, 2nd, 3rd, 4th or 5th gear position). When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.INSPECTION PROCEDURE
| ACTIVE TEST |
- HINT:
- Performing the intelligent tester Active Test allows relay, Vacuum Switching Valve (VSV), actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to shorten labor time.
- The Data List can be displayed during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Enter / Powertrain / ECT / Active Test".
Follow the instructions on the tester and read the Active Test.
- HINT:
- While driving, the shift position can be forcibly changed with the intelligent tester.
- Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you to confirm the problem (Click here).
Item
Test Details
Diagnostic Note
Control Shift Position
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]- Less than 50 km/h (31 mph)
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check the operation of the shift solenoid valves.
- HINT:
- This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
- The shift position commanded by the ECM is shown in the DATA LIST (Shift Status) display on the intelligent tester.
- This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
| 1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0766) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
- Result:
Display (DTC output)
Proceed to
Only "P0766" is output
A
"P0766" and other DTCs
B
- HINT:
- If any other codes besides "P0766" are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. INSPECT SHIFT SOLENOID VALVE S4 |
Remove the shift solenoid valve S4.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
20°C (68°F)
Solenoid Connector (S4) - Solenoid Body (S4)
11 to 15 Ω
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
- OK:
- The solenoid makes an operating sound.
|
|
||||
| OK | |
| 3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
- OK:
- There are no foreign objects on each valve and the valves operate smoothly.
|
|
||||
| OK | |
| 4. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
