P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
SYSTEM DESCRIPTION
The shift solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The TCM adjusts the duty ratio (*) of the SLT solenoid valve to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle. For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then
Duty Ratio = A/(A + B ) x 100 (%)


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2714 |
The TCM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the transmission fluid pressure. (2-trip detection logic) |
|
MONITOR DESCRIPTION
The TCM calculates the amount of clutch slip based on the turbine speed, output shaft speed, and gear ratio. If the amount of clutch slip exceeds a specified level, the TCM will set this DTC and illuminate the MIL.When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.
- NOTICE:
- If driving continues under these conditions, the clutches will burn out and the vehicle will no longer be drivable.
INSPECTION PROCEDURE
| 1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester on.
Enter the following items: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
- Result:
Display (DTC output)
Proceed to
Only "P2714" is output
A
"P2714" and other DTCs are output
B
- HINT:
- If a solenoid is stuck ON, DTCs for several solenoids including the malfunctioning solenoid will be detected.
|
|
||||
| B | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT) |
- NOTICE:
- Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F)
- Be sure to prevent the SST hose from interfering with the exhaust pipe.
- This check must be conducted after checking and adjusting the engine.
- Perform the test with the A/C OFF.
- Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F)
- HINT:
- Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and other items to operate without removing any parts. Performing the Active Test as the first step in troubleshooting is one method to save diagnostic time.
- It is possible to display the Data List during the Active Test.
Turn the ignition switch off.
Lift the vehicle up.
Remove the test plug on the transmission case center right side and connect SST.

- SST
- 09992-00095
(09992-00231, 09992-00271)
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the intelligent tester to the DLC3.
Start the engine.
Warm up the ATF (Automatic Transmission Fluid).
Measure the line pressure when the engine is idling.
Turn on the tester.
Enter the following items: "Powertrain / ECT / Active Test / Activate the Solenoid (SLT)".
Follow the instructions on the tester and perform the Active Test.
Measure the line pressure with SST.
*: "Activate the Solenoid (SLT)" in the Active Test is performed to check that the line pressure changes by connecting the SST to the automatic transaxle. The same SST is used in the Hydraulic Test (Click here) as well.Tester Display
Test Part
Control Range
Activate the Solenoid (SLT)*
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]- Vehicle stopped.
- IDL: ON
- HINT:
- OFF: Line pressure up (When the active test of "Solenoid (SLT)" is performed, the TCM commands the SLT solenoid to turn off).
- ON: No action (normal operation)
[Solenoid (SLT)]
0: OFF / 1: ON
- HINT:
- The pressure values in Active Test and HYDRAULIC TEST are different from each other.
- OK:
- The line pressure changes as specified when performing the Active Test.
- Vehicle stopped.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFTING TEST) |
- NOTICE:
- This test should always be performed by at least 2 people.
- HINT:
- Performing the Active Test using the intelligent tester allows relays, VSVs, actuators and other items to be operated without removing any parts. Performing the Active Test as the first step in troubleshooting is one method to save diagnostic time.
- The Data List can be displayed during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn on the tester.
Enter the following items: "Powertrain / ECT / Active Test".
Follow the instructions on the tester and perform the Active Test.
Item
Test Details
Diagnostic Note
Control the Shift Position
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]- IDL: ON
- Press "→" button: Shift up
- Press "←" button: Shift down
It is possible to check the operation of the shift solenoid valves.
- NOTICE:
- This test can be conducted when the vehicle is stopped.
- When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.
- This test can be conducted when the vehicle is stopped.
- HINT:
- The shift position commanded by the TCM is shown on the "Data List / Shift Status" display on the intelligent tester.
- IDL: ON
Check the vehicle speed and the gear position when the engine speed is 1,000 rpm.
- HINT:
- Because the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gears, however a difference of speed should still be evident following each gear change.
- Standard:
1st
2nd
3rd
4th
5th
6th
8 to 12 km/h (5 to 7.5 mph)
15 to 19 km/h (9.3 to 11.8 mph)
21 to 25 km/h (13.0 to 15.5 mph)
31 to 35 km/h (19.3 to 21.7 mph)
44 to 48 km/h (27.3 to 29.8 mph)
52 to 56 km/h (32.3 to 34.8 mph)
Compare the TCM gear shift command and the actual gear position.
- Result:
Actuator gear position under malfunction
TCM gear shift command
Proceed to
1st
2nd
3rd
4th
5th
6th
Shift solenoid SL1
Stuck ON
1st
2nd
3rd
4th
4th
4th
A
Stuck OFF
N*1
N*1
N*1
N*1
5th
6th
Shift solenoid SL2
Stuck ON
4th
4th
4th
4th
5th
6th
B
Stuck OFF
1st
2nd
3rd
1st
N*1
N*1
Shift solenoid SL3
Stuck ON
2nd
2nd
3rd
4th
5th
6th
C
Stuck OFF
1st
1st
3rd
4th
5th
N*1
Shift solenoid SL4
Stuck ON*3
3rd
3rd
3rd
4th
5th
5th
D
Stuck OFF
1st
2nd
1st
4th
N*1
6th
Shift solenoid SLT
Stuck ON
N*2
N*2
N*2
N*2
N*2
N*2
E
Stuck OFF*3
1st
2nd
3rd
4th
5th
6th
- HINT:
- *1: Neutral
- *2: If the shift solenoid SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
- *3: When the shift solenoid SLT is stuck OFF, gear shifting is normal.
- *1: Neutral
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| E | |
| 4. INSPECT SHIFT SOLENOID VALVE SLT |
Remove the shift solenoid valve SLT.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
1 - 2
5.0 to 5.6 Ω
(at 20°C (68°F))
Connect a positive (+) lead through a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
- OK:
- The solenoid makes an operating sound.
|
|
||||
| OK | |
| 5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the valve body assembly (Click here).
- OK:
- There are no foreign objects on each valve and the valves operate smoothly.
|
|
||||
| OK | |
| 6. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
