2006-2011 Camry Aurion · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. PRECAUTION

HINT:
(Click here)


2. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


4. REMOVE FRONT WHEEL LH

5. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B132067
    Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.


6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B132116E01
    Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.


7. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (for 2GR-FE RHD)

  1. B158913E01
    Remove the bolt <D> and the screw <F>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect each connector, and then remove the lower No. 1 instrument panel finish panel.


8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL (except 2GR-FE RHD)

  1. B147264E01
    Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.


9. REMOVE NO. 2 LOWER STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.

    C146013E01

    HINT:
    Tape up the screwdriver tip before use.


10. REMOVE NO. 3 LOWER STEERING WHEEL COVER

  1. Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.

    C146012E01

    HINT:
    Tape up the screwdriver tip before use.


11. REMOVE STEERING PAD

  1. Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    C146014E01

  1. C133859E01
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector from the steering pad.

  1. Disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


12. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C145839E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)


13. REMOVE LOWER STEERING COLUMN COVER

  1. C145841
    Remove the 2 screws.

  1. Disengage the 2 claws to remove the lower steering column cover.


14. REMOVE UPPER STEERING COLUMN COVER

  1. C145842
    Disengage the claw to remove the upper steering column cover.


15. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C145843
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


16. REMOVE NO. 1 AIR DUCT

  1. C132547E01
    Disengage the 2 claws and remove the No. 1 air duct.


17. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C133172
    Remove the clamp from the steering column hole shield.

  1. C132548E02
    Remove the bolt.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C132549E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


18. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.

  1. C145844E01
    Remove the bolt, 2 nuts, and the steering column assembly.


19. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C145838E01
    Put matchmarks on the steering intermediate shaft assembly and the steering column assembly.

  1. Remove the bolt and the steering intermediate shaft assembly from the steering column assembly.

← REMOVAL (Oct 2006 – May 2009)DISASSEMBLY (Jun 2006 – Sep 2006) →