2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Open in CAN Main Bus Line

Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006

DESCRIPTION

There may be an open circuit in the CAN main bus wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or more.
  1. CAN main bus wire or connector
  2. No. 1 CAN J/C
  3. No. 4 CAN J/C
  4. DLC3 branch wire or connector
  5. Combination meter
  6. ECM

WIRING DIAGRAM

C133283E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK DLC3
  1. Turn the ignition switch off.

  1. C126231E11
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    E10-6 (CANH) -E10-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    A
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    132 Ω or higher
    B

    NOTICE:
    When the measured value is 132 Ω or more and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here ) after repairing the trouble area.



B
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR (CANH, CANL)
A


2. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER MAIN BUS WIRE)

  1. C133231E05
    Disconnect the CAN main bus wire connector (E43) from the No. 1 CAN J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E43-1 (CANH) - E43-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 6
OK


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN J/C)
  1. Reconnect the CAN main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).

  1. C133228E02
    Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E42-1 (CANH) - E42-2 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE NO. 1 CAN J/C
NG


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 CAN J/C - ECM)
  1. Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C (with earth terminal).

  1. C133245E22
    Disconnect the CAN main bus wire connector (A40) from the No. 4 CAN J/C (rear of the vehicle).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - A40-7 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 7
NG


5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM CAN MAIN BUS WIRE)
  1. Reconnect the CAN main bus wire connector (A40) to the No. 4 CAN J/C (rear of the vehicle).

  1. G100098E14
    Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-41 (CANH) - A24-49 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 4 CAN J/C - ECM)

6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 1 CAN J/C)
  1. Reconnect the CAN main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).

  1. C133243E03
    Disconnect the combination meter connector (F1).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-23 (CANH) - F1-22 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE COMBINATION METER
NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN J/C - COMBINATION METER)

7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN J/C - NO. 4 CAN J/C)

  1. C133246E23
    Reconnect the CAN main bus wire connector (A40) to the No. 4 CAN J/C (rear of the vehicle).

  1. Disconnect the CAN main bus wire connector (E41) from the No. 4 CAN J/C (rear of the vehicle).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    E41-4 (CANH) - E41-10 (CANL)
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN J/C - NO. 4 CAN J/C)
OK

REPLACE NO. 4 CAN J/C


← CAN Bus Line (Jun 2006 – Sep 2006)Short in CAN Bus Lines (Jun 2006 – Sep 2006) →