2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Open in CAN Main Bus Line

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

There may be an open circuit in the CAN main bus wire and/or the DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or more.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or more.
  1. CAN main bus wire or connector
  2. No. 1 CAN J/C
  3. No. 4 CAN J/C
  4. DLC3 branch wire or connector
  5. Combination meter
  6. ECM

WIRING DIAGRAM

C123381E11

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK DLC3

  1. C126231E11
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Result
    E10-6 (CANH) -E10-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    A
    E10-6 (CANH) - E10-14 (CANL)
    Ignition switch off
    133 Ω or higher
    B

    NOTICE:
    When the measured value is 133 Ω or more and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here) after repairing the trouble area.



B
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR (CANH, CANL)
A


2. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER MAIN BUS WIRE)

  1. C145032E01
    Disconnect the CAN main bus wire connector (E43) from the No. 1 CAN J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E43-1 (CANH) - E43-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 7
OK


3. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN J/C)

  1. C142742E04
    Reconnect the CAN main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).

  1. Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E42-1 (CANH) - E42-2 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE NO. 1 CAN J/C
NG


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 CAN J/C - NO. 4 CAN J/C)
  1. Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).

  1. C133246E23
    Disconnect the CAN main bus wire connector (E41) from the No. 4 CAN J/C (front of the vehicle).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-4 (CANH) - E41-10 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN J/C - NO. 4 CAN J/C)
OK


5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 4 CAN J/C)

  1. C133245E22
    Reconnect the CAN main bus wire connector (E41) to the No. 4 CAN J/C (front of the vehicle).

  1. Disconnect the CAN main bus wire connector (A40) from the No. 4 CAN J/C (rear of the vehicle).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - A40-7 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE NO. 4 CAN J/C
NG


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM CAN MAIN BUS WIRE)

  1. G100098E23
    Reconnect the CAN main bus wire connector (A40) to the No. 4 CAN J/C (rear of the vehicle).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    2AZ-FE:
    Tester Connection
    Condition
    Specified Condition
    A24-41 (CANH) - A24-49 (CANL)
    Ignition switch off
    108 to 132 Ω
    2GR-FE:
    Tester Connection
    Condition
    Specified Value
    A55-41 (CANH) - A55-49 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 4 CAN J/C - ECM)

7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 1 CAN J/C)
  1. Reconnect the CAN main bus wire connector (E43) to the No. 1 CAN J/C "B" side (without earth terminal).

  1. Disconnect the combination meter connector (F1).

  1. C133243E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    2AZ-FE:
    Tester Connection
    Condition
    Specified Condition
    F1-23 (CANH) - F1-22 (CANL)
    Ignition switch off
    108 to 132 Ω

  1. C133243E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    2GR-FE:
    Tester Connection
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE COMBINATION METER
NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN J/C - COMBINATION METER)


← Open in CAN Main Bus Line (Oct 2006 – May 2009)Short in CAN Bus Lines (Oct 2006 – May 2009) →