2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

Short to B+ in CAN Bus Line

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

A short to B+ is suspected in the CAN bus wire when the resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short to B+ in CAN bus wire
  2. Skid control ECU
  3. ECM
  4. Main body ECU
  5. A/C amplifier
  6. Center airbag sensor assembly
  7. Combination meter

WIRING DIAGRAM

C144949E05

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


1. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. C152843E01
    Disconnect the DLC3 branch wire connector (E62) from the No. 1 CAN J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. C126231E12
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

  1. Reconnect the DLC3 branch wire connector (E62) to the No. 1 CAN J/C "B" side (without earth terminal).



NG
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR
OK


2. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN J/C SIDE)

  1. C142742E04
    Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

  1. C126231E12
    Measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



OK
Go to step 6
NG


3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE

  1. C126231E12
    Disconnect connectors from the No. 1 CAN J/C one at a time.

    HINT:
    Disconnect the ECU and sensor connectors other than the DLC3 branch wires and CAN main bus wires between the No. 1 CAN J/C and No. 4 CAN J/C.

  1. Measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.C144959E02
    C144992E02

    No. 1 CAN J/C Connector ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    No. 1 CAN J/C Connector ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to B+ in 2 or more CAN bus wires.

  1. When there is a short to B+ in one or more of the bus wires that connect to an ECU (or sensor):

    1. Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the bus wire that is shorted to B+). Check that the resistance shown on the tester is normal (6 kΩ or more) to confirm that there is a short to B+ in one bus wire only.

      HINT:
      1. The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
      2. Reconnecting the connectors to non-specified positions on the No. 1 CAN J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


NEXT


4. RECONNECT CONNECTOR
  1. Reconnect the connector of the bus wire that is shorted to B+ to the No. 1 CAN J/C (the connector that caused the bus wire resistance to change to 6 kΩ or more when it was disconnected).


NEXT


5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE

  1. C126231E12
    Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to B+ is connected. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    HINT:
    If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR

6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE

  1. C133245E17
    Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).

  1. Disconnect the No. 4 CAN J/C connector (A40).

  1. C126231E12
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



OK
Go to step 10
NG


7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN J/C - NO. 4 CAN J/C)

  1. C133246E24
    Disconnect the No. 4 CAN J/C connector (E41).

  1. C126231E12
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-6 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    HINT:
    Measure the resistance with the No. 4 CAN J/C connector (A40) disconnected.



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE (NO. 1 CAN J/C - NO. 4 CAN J/C)
OK


8. RECONNECT CONNECTOR
  1. Reconnect the No. 4 CAN J/C connector (A40).


NEXT


9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (A/C AMPLIFIER)

  1. C133246E22
    Disconnect the A/C amplifier connector (E38).

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E41-7 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    HINT:
    Measure the resistance with the No. 4 CAN J/C connector (E41) disconnected.



NG
REPAIR OR REPLACE A/C AMPLIFIER BRANCH WIRE OR CONNECTOR
OK

REPLACE A/C AMPLIFIER

10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN BUS WIRE)

  1. C133245E22
    Disconnect the No. 4 CAN J/C connector (A40).

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A40-7 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



OK
Go to step 12
NG


11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)

  1. C133245E22
    Disconnect the ECM connector (A24 or A55).

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A40-7 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    HINT:
    Measure the resistance with the No. 4 CAN J/C connector (A40) disconnected.



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM - NO. 4 CAN J/C)
OK

REPLACE ECM

12. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C133245E19
    C126231E14
    Disconnect the skid control ECU connector (A25).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A40-2 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A40-8 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



OK
REPLACE BRAKE ACTUATOR ASSEMBLY
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR


← Short to B+ in CAN Bus Line (Oct 2006 – May 2009)Short to GND in CAN Bus Line (Oct 2006 – May 2009) →