Short to GND in CAN Bus Line
Circuit diagnosis · Vehicles built Jun 2006 – Sep 2006
DESCRIPTION
A short to GND is suspected in the CAN bus wire when the resistance between terminals 4 (CG) and 6 (CANH), or terminals 4 (CG) and 14 (CANL) of the DLC3 is below 200 Ω.| Symptoms |
Trouble Area |
| The resistance between terminals 6 (CANH) and 4 (CG), or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of CAN main wires and CAN branch wires.
- HINT:
- Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
Turn the ignition switch off.

Disconnect the DLC3 branch wire connector (E41) from the No. 4 CAN J/C (front of the vehicle).
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
E10-14 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
Reconnect the DLC3 branch wire connector (E41) to the No. 4 CAN J/C (front of the vehicle).
|
|
||||
| OK | |
| 2. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN J/C SIDE) |
Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).

Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
E10-14 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | |
| 3. CHECK FOR SHORT TO GND IN CAN BUS WIRE |
Reconnect the CAN main bus wire connector (E42).

Disconnect connectors from the No. 1 CAN J/C one at a time.
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.




No. 1 CAN J/C Connector ("A" side, with earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
Center Airbag Sensor Assembly (E45)
Black
B
W
*: with VSCNo. 1 CAN J/C Connector ("B" side, without earth terminal)
Connector Color
Wire Color (CAN-H)
Wire Color (CAN-L)
Yaw Rate Sensor (E46)*
Blue
B
W
A/C Amplifier (E47)
Gray
B
W
Combination Meter (E43)
White
B
W
Main Body ECU (E44)
Black
B
W
- NOTICE:
- Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus wires.
When there is a short to GND in one or more of the bus wires that connect to an ECU (or sensor):
Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the bus wire that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or more) to confirm that there is a short to GND in one branch wire only.
- HINT:
- The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
- Reconnecting the connectors to non-specified positions on the No. 1 CAN J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
- The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
| NEXT | |
| 4. RECONNECT CONNECTOR |
Reconnect the connector of the bus wire that is shorted to GND to the No. 1 CAN J/C (the connector that caused the bus wire resistance to change to 200 Ω or more when it was disconnected).
| NEXT | |
| 5. CHECK FOR SHORT TO GND IN CAN BUS WIRE |
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to GND is connected (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
E10-14 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
- HINT:
- If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
|
|
||||
| OK | ||
| ||
| 6. CHECK FOR SHORT TO GND IN CAN BUS WIRE |
Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C "A" side (with earth terminal).
Disconnect the No. 4 CAN J/C connector (A40).

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E10-6 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
E10-14 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| NG | |
| 7. RECONNECT CONNECTOR |
Reconnect the No. 4 CAN J/C connector (A40).
| NEXT | |
| 8. CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE) |
Disconnect the No. 4 CAN J/C connector (E41).

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E41-3 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
E41-9 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| NG | |
| 9. CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR) |
Disconnect the steering angle sensor connector (E17).

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
E41-3 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
E41-9 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM MAIN BUS WIRE) |
Disconnect the No. 4 CAN J/C connector (A40).

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-1 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
A40-7 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| NG | |
| 11. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM) |
Disconnect the ECM connector (A24).

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-1 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
A40-7 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | ||
| ||
| 12. CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU) |
Disconnect the skid control ECU connector (A25) or (A26).

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
A40-2 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
A40-8 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| NG | ||
| ||
