2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Driver Side Door UNLOCK Detection Switch Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The driver's door unlock detection switch is built into the driver's door lock assembly. The switch turns on when the driver's door is locked and turns off when the door is unlocked.
The main body ECU (instrument panel J/B) is connected to the driver's door lock assembly via terminal LSWD and driver's door lock/unlock state signals are input to the main body ECU (instrument panel J/B).
The main body ECU (instrument panel J/B) applies voltage to the door unlock detection switch via terminal LSWD. When the door unlock detection switch is on (there is continuity between the switch terminals), a lock state signal is input to the main body ECU (instrument panel J/B). When the switch is off (there is no continuity between the switch terminals), an unlock state signal is input.

WIRING DIAGRAM

B150880E01

INSPECTION PROCEDURE


1. READ VALUE ON INTELLIGENT TESTER

  1. Connect the intelligent tester to the DLC3.B150920E01

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select D-Door Lock Pos SW in the DATA LIST and read the tester display.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Lock Pos SW
    Driver side door unlock detection switch signal / ON or OFF
    ON: Driver side door is unlocked
    OFF: Driver side door is locked
    -

    OK:
    The display is as specified in the "Normal Condition" column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR UNLOCK DETECTION SWITCH)

  1. Remove the front door lock assembly (driver side) (Click here).B150907E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Measurement Condition
    Door Lock Condition
    Specified Condition
    7 - 8
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Lock
    10 kΩ or higher
    7 - 8
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlock
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU)

  1. B112606E08
    Disconnect the main body ECU (instrument panel J/B) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    I7-8 (LSSR) - E7-9 (LSWD)
    Always
    Below 1 Ω
    I7-8 (LSSR) - Body ground
    Always
    10 kΩ or higher
    I7-7 (E) - Body ground
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    H8-7 (LSSR) - E7-9 (LSWD)
    Always
    Below 1 Ω
    H8-7 (LSSR) - Body ground
    Always
    10 kΩ or higher
    H8-8 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL J/B)


← Driver Side Door UNLOCK Detection Switch Circuit (Oct 2006 – May 2009)Front Passenger Side Door UNLOCK Detection Switch Circuit (Oct 2006 – May 2009) →