2006-2011 Camry Aurion · Service Manual BODY

ADJUSTMENT

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

B146088E01

HINT:
  1. Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts (with washers) when making adjustments.
  2. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. REMOVE COOL AIR INTAKE DUCT SEAL (for 2GR-FE)

  1. B232362
    Remove the 7 clips and cool air intake duct seal.


2. REMOVE FRONT BUMPER ASSEMBLY (for 2AZ-FE)

  1. B220943E01
    Put protective tape around the front bumper assembly.

  1. B138884E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B220944
    Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.

  1. B220945
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. w/o Fog Light:

    1. Remove the front bumper assembly.

  1. w/ Fog Light:

    1. Disconnect each connector, and then remove the front bumper assembly.


3. REMOVE FRONT BUMPER ASSEMBLY (for 2GR-FE)

  1. B232367E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B232368
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B232369
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. w/ Clearance Sonar System:

    1. Disconnect the 2 connectors.

  1. w/ Fog Light:

    1. Disconnect the 2 connectors.

  1. w/ Headlight Cleaner System:

    1. Disconnect the 2 connectors.

    2. B149621
      Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.

  1. Remove the front bumper assembly.


4. ADJUST HOOD SUB-ASSEMBLY

  1. Horizontally and vertically adjust the hood.

    1. B132829
      Loosen the 4 hinge bolts of the hood.

    2. Adjust the clearance between the hood and front fender by moving the hood.

    3. Tighten the 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Adjust the height of the front end of the hood using the cushion rubber.

    1. B132830
      Adjust the cushion rubber so that the height of the hood and fender are aligned.

      HINT:
      Raise or lower the front end of the hood by turning the cushion rubber.

  1. Adjust the hood lock.

    1. B148998
      Loosen the 3 bolts.

    2. Tighten the bolts after the adjustment.

      Torque:
      7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

    3. Check that the striker can engage with the hood lock smoothly.


5. INSTALL FRONT BUMPER ASSEMBLY (for 2AZ-FE)
  1. w/ Fog Light:

    1. Connect each connector.

  1. B221322
    Engage the 2 claws.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B220944
    Install the front bumper assembly with the 8 screws, 2 clips, 2 radiator grille protectors and bolt.

  1. B221988E02
    Install the pin hold clip.

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is vertically oriented.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B220943E01
    Remove the applied protective tape from the front bumper assembly.


6. INSTALL FRONT BUMPER ASSEMBLY (for 2GR-FE)
  1. w/ Clearance Sonar System:

    1. Connect the 2 connectors.

  1. w/ Fog Light:

    1. Connect the 2 connectors.

  1. w/ Headlight Cleaner System:

    1. Connect the 2 connectors.

    2. B149621
      Connect the headlight cleaner washer hose.

  1. B232370
    Engage the 2 claws.

  1. B232368
    Install the front bumper assembly with the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B221988E02
    Install the pin hold clip.

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertical.

    HINT:
    Use the same procedure for the RH side and LH side.


7. INSTALL COOL AIR INTAKE DUCT SEAL (for 2GR-FE)

  1. B232362
    Install the cool air intake duct seal with the 7 clips.


8. VEHICLE PREPARATION FOR FOG LIGHT AIM ADJUSTMENT
  1. Prepare the vehicle:

    1. Ensure that there is no damage or deformation to the body around the fog lights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the engine coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Unload the trunk and vehicle, ensuring that the spare tire, tools, and jack are in their original positions.
    7. Sit a person of average weight (75 kg, 165 lb) in the driver's seat.
    8. Vehicles with height adjustable suspension should set the vehicle height to the lowest setting prior to adjusting the fog light aim.


9. PREPARATION FOR FOG LIGHT AIMING

  1. E128202E02
    Prepare the vehicle:
    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Create a 25 m (82 ft) distance between the vehicle (fog light bulb center) and the wall.
    4. Make sure that the vehicle is on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 25 m (82 ft) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If sufficient space is not available, secure a distance of exactly 3 m (9.84 ft) to allow for checking and adjustment of fog light aim. (The size of the target zone will change with the distance, so follow the instructions in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of the screen (V line).

  1. Set the screen as shown in the illustration.

    E137527E01

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.

  1. I033423E15
    Draw base lines (H, V LH, and V RH lines) on the screen as shown in the illustration.

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.


10. FOG LIGHT AIMING INSPECTION
  1. Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

    NOTICE:
    Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.

  1. Start the engine.

  1. Turn on the fog light and check if the cut off line falls within the specified area in the following illustration.

    I041221E20


11. FOG LIGHT AIMING ADJUSTMENT

  1. E128204E01
    Adjust the aim vertically:
    Adjust the aim of each fog light to the specified range by turning each aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.

    HINT:
    If it is not possible to correctly adjust fog light aim, check bulb, fog light unit, and fog light unit reflector installation.

← ADJUSTMENT (Oct 2006 – May 2009)COMPONENTS (Jun 2006 – Sep 2006) →