P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009
Also covers:
- P0724 Brake Switch "B" Circuit High
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.- HINT:
- The normal conditions are as shown in the table below. The signals can be read using an intelligent tester.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch on (IG) (b) Brake pedal released (c) STP signal OFF when ST1- signal OFF |
|
| P0724 |
The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3km/h (2mph)) and GO ( 30 km/h (19 mph) or more) fashion 5 times. (2 trip detection logic) |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).
| 1. CHECK STOP LIGHT (OPERATION OF STOP LIGHT) |
Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.
- OK:
- Stop lights turn ON when brake pedal is depressed.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1 - VOLTAGE) |
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch.
Check the STP signal when the brake pedal is depressed and released.
- OK:
Brake Pedal Operation
Specified Condition
Depressed
STP signal ON
Released
STP signal OFF
Enter the following menus: Powertrain / Engine / Data List / ST1.
Check the ST1 signal when the brake pedal is depressed and released.
- OK:
Brake Pedal Operation
Specified Condition
Depressed
ST1 signal OFF
Released
ST1 signal ON
|
|
||||
| NG | |
| 3. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Remove the stop light switch assembly.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Switch Position
Tester Connection
Specified Condition
Switch pin free
1 - 2
Below 1 Ω
Switch pin free
3 - 4
10 kΩ or higher
Switch pin pushed in
1 - 2
10 kΩ or higher
Switch pin pushed in
3 - 4
Below 1 Ω
Reinstall the stop light switch assembly.
|
|
||||
| OK | |
| 4. CHECK ECM (STP, ST1 - VOLTAGE) |
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
- RHD:
Tester Connection
Brake Pedal Operation
Specified Condition
STP (A24-36) - Body ground
Depressed
9 to 14 V
STP (A24-36) - Body ground
Released
0 to 3 V
ST1- (A24-35) - Body ground
Depressed
0 to 3 V
ST1- (A24-35) - Body ground
Released
9 to 14 V
- LHD:
Tester Connection
Brake Pedal Operation
Specified Condition
STP (A55-36) - Body ground
Depressed
9 to 14 V
STP (A55-36) - Body ground
Released
0 to 3 V
ST1- (A55-35) - Body ground
Depressed
0 to 3 V
ST1- (A55-35) - Body ground
Released
9 to 14 V
|
|
||||
| OK | ||
| ||
