2006-2011 Camry Aurion · Service Manual ENGINE

B2282 Vehicle Speed Signal Malfunction

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Also covers:

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The skid control ECU converts these signals into 4-pulse signals and sends them to the combination meter. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the main body ECU. The main body ECU determines the vehicle speed based on the frequency of these pulse signals.
The main body ECU and the combination meter are connected by a cable and the CAN. DTC B2282 is output when the cable information and CAN information are inconsistent.

HINT:
When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2282
Cable information and CAN information between the main body ECU and the combination meter are inconsistent
  1. CAN communication system
  2. Combination meter system
  3. Main body ECU
  4. Wire harness or connector
B2283
When either of conditions below are met:
  1. Over-deceleration in vehicle speed
  2. Vehicle speed and engine speed do not match
  1. DTC B2282 detection area
  2. Combination meter
  3. Speed sensor
  4. Main body ECU
  5. Wire harness or connector
B138069E01

WIRING DIAGRAM

B162646E01

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in an ECU, all systems in the diagram above will not operate normally.


INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check for CAN communication system DTCs (for LHD: Click here), (for RHD: Click here).

    HINT:
    If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first.


    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output (for LHD).
    B
    CAN communication DTC is output (for RHD.
    C



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCs (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCs (Click here)
A


2. CHECK COMBINATION METER SYSTEM
  1. The circuits that send vehicle speed signals to this system are inspected in the meter system (Click here).

  1. During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


NEXT


3. CHECK HARNESS AND CONNECTOR (COMBINATION METER - MAIN BODY ECU)

  1. Disconnect the F2 meter connector.B137982E04

  1. Disconnect the E8 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-9 (SPD) - F2-12 (+S)
    Always
    Below 1Ω



NG
Go to step 4
OK

REPLACE MAIN BODY ECU

4. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - NO. 3 JUNCTION BLOCK)
  1. Disconnect the 3M junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-9 (SPD) - 3M-10
    Always
    Below 1Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (MAIN BODY ECU - NO. 3 JUNCTION BLOCK)
OK

REPLACE NO. 3 JUNCTION BLOCK (NO. 3 JUNCTION BLOCK)


← B2281 "P" Signal Malfunction (from Jun 2009)B2282 Vehicle Speed Signal Malfunction (+ B2283) (from Jun 2009) →