2006-2011 Camry Aurion · Service Manual BRAKE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


FREEZE FRAME DATA
  1. Whenever an ABS DTC is detected, the skid control ECU stores the current vehicle (sensor) status as Freeze Frame Data.

  2. The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to the on (IG) since the last time the ABS was activated.

    HINT:
    1. However, if the vehicle is stopped or at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU will stop counting the number.
    2. Freeze Frame Data at the time the ABS operates:
      The skid control ECU stores and updates data whenever the ABS system operates.
      When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.
    3. Freeze Frame Data at the time a DTC is detected:
      When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Select the "DTC" on the tester display.

  6. On the DTC data display screen, select the DTC data display with "!".

    Intelligent Tester Display
    Measurement Item
    Reference Value
    Elapsed Time after Freeze Trigger
    Elapsed time after freeze trigger
    Min.: 0 ms, Max.: 500 ms
    Number of IG ON
    Number of operations of ignition switch on (IG) after storing freeze frame data
    0 to 31
    Buzzer
    Skid control buzzer signal
    Skid control buzzer ON: ON, OFF: OFF
    Stop Lamp SW
    Stop light switch signal
    Stop light switch ON: ON, OFF: OFF
    Parking Brake SW
    Parking brake switch signal
    Parking brake switch ON: ON, OFF: OFF
    Gear Position
    Gear position information
    FAIL
    1st
    2nd
    3rd
    4th
    5th
    6th
    P, N
    R
    NOT R
    Shift Lever Position
    Shift lever position information
    FAIL
    1st
    2nd
    3rd
    4th
    5th
    6th/B
    D/M
    P, N
    R
    Operated System
    Operated system status
    ABS activated: ABS
    VSC activated: VSC
    TRC activated: TRC
    BA activated: BA
    PB activated: PB
    Fail safe mode activated: FAIL
    No system activated: NON
    System prohibited: SYS
    Master Cylinder Sensor
    Master cylinder pressure sensor reading
    Brake pedal released: 0.1 to 0.9 V
    M/C Sensor Grade
    Master cylinder pressure sensor change
    Min.: -30 MPa/s, Max.: 225 MPa/s
    Yaw Rate Sensor
    Yaw rate sensor reading
    Min.: -128 deg/s, Max.: 127 deg/s
    Lateral G
    Lateral G
    Min.: -25.11 m/s2, Max.: 24.91 m/s2
    Forward and Rearward G
    Forward and backward G
    Min.: -25.11 m/s2, Max.: 24.91 m/s2
    FR Wheel Speed
    FR wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    FL Wheel Speed
    FL wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    RR Wheel Speed
    RR wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    RL Wheel Speed
    RL wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle Speed
    Vehicle speed reading
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle Speed Grade
    Vehicle speed grade
    Min.: -25.11 m/s2, Max.: 24.91 m/s2
    Real Engine Torque
    Real engine torque
    Min.: -1024 Nm, Max.: 1023 Nm
    Engine Revolutions
    Engine revolutions
    Min.: 0 r/min.
    Max.: 65,535 r/min.
    Inspection Mode
    Inspection mode
    OTHER: Normal,
    INSPECT: Service
    Steering Angle Sensor
    Steering angle sensor reading
    Left turn: Increase
    Right turn: Decrease

← FREEZE FRAME DATA (Oct 2006 – May 2009)FAIL-SAFE CHART (Jun 2006 – Sep 2006) →