2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the CAN main wire and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or any doors triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR (CAN NO. 1 J/C, CAN NO. 4 J/C)

  1. CAN No. 1 J/C
    C145010E01

    CAN No. 1 J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    CAN Main Bus Wire (E42)
    White
    B
    W
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    CAN No. 1 J/C connectors ("B" side, without earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    A/C Amplifier (E47)
    Gray
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    Yaw Rate Sensor (E46)*
    Blue
    B
    W
    *: with VSC

  2. CAN No. 4 J/C (REAR OF THE VEHICLE)
    C137762E08

    Terminals
    Wiring Color
    Connects to
    A40-1 (CANH)
    B
    ECM (CANH)
    A40-7 (CANL)
    W
    ECM (CANL)
    A40-2 (CANH)
    B
    Skid Control ECU (CANH)
    A40-8 (CANL)
    W
    Skid Control ECU (CANL)

  3. CAN No. 4 J/C (FRONT OF THE VEHICLE)
    C137763E29

    Terminals
    Wiring Color
    Connects to
    E41-2 (CANH)
    B
    DLC3 (CANH)
    E41-8 (CANL)
    W
    DLC3 (CANL)
    E41-4 (CANH)
    B
    CAN No. 1 J/C (CANH)
    E41-10 (CANL)
    W
    CAN No. 1 J/C (CANL)
    E41-3 (CANH)
    B
    Steering Angle Sensor (CANH)
    E41-9 (CANL)
    W
    Steering Angle Sensor (CANL)

  4. The connection diagram of the components which are connected to the CAN No. 4 J/C
    C142793E02


JUNCTION CONNECTOR FOR CAN MS BUS (w/ CLEARANCE SONAR SYSTEM (w/ CORNER SENSOR))

  1. CAN No. 3 J/C
    C144961E02

    CAN No. 3 J/C Connector ("A" side, with earth terminal)
    Connector Color
    Color (CAN-H Side)
    Color (CAN-L Side)
    Clearance Warning ECU (O32)
    Blue
    L
    W
    CAN MS Bus Main Wire (O33)
    White
    L
    W


DLC3

  1. C125062E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E10-6 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E10-6 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


SKID CONTROL ECU (w/o VSC)

  1. C131970E14
    Disconnect the A25 skid control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-26 (CANH) - A25-15 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    A25-26 (CANH) - A25-4 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A25-15 (CANL) - A25-4 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A25-26 (CANH) - A25-3 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    A25-15 (CANL) - A25-3 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR (w/ VSC)

  1. C136493E11
    Disconnect the A26 skid control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    A26-35 (CANH) - A26-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition switch off
    54 to 69 Ω
    A26-35 (CANH) - A26-4 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    A26-14 (CANL) - A26-4 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    A26-35 (CANH) - A26-3 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    A26-14 (CANL) - A26-3 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher


STEERING ANGLE SENSOR (w/ VSC)

  1. G026357E15
    Disconnect the E17 steering angle sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E17-10 (CANH) - E17-9 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition switch off
    54 to 69 Ω
    E17-10 (CANH) - E17-2 (ESS)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E17-9 (CANL) - E17-2 (ESS)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E17-10 (CANH) - E17-3 (BAT)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    E17-9 (CANL) - E17-3 (BAT)
    W - W
    LOW-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR (w/ VSC)

  1. C225737E01
    Disconnect the E34 yaw rate sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E34-2 (CANH) - E34-3 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition switch off
    54 to 69 Ω
    E34-2 (CANH) - E34-4 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E34-3 (CANL) - E34-4 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E34-2 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    E34-3 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher


CENTER AIRBAG SENSOR

  1. C125063E06
    Disconnect the E30 center airbag sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E30-13 (CANH) - E30-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E30-13 (CANH) - E30-25 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E30-22 (CANL) - E30-25 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E30-13 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    E30-22 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


ECM

  1. Measure the resistance according to the value(s) in the table below.
    A107881E72

    Standard resistance:
    Terminals
    Condition
    Specified Condition
    A24-41 (CANH) - A24-49 (CANL)
    Ignition Switch off
    108 to 132 Ω

  2. C136709E07
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-41 (CANH) - A24-49 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    A24-41 (CANH) - C58-81 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A24-49 (CANL) - C58-81 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A24-41 (CANH) - A24-20 (BATT)
    B - Y
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    A24-49 (CANL) - A24-20 (BATT)
    W - Y
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER

  1. E124470E20
    Check the harness side connector (E38) of the air conditioning amplifier.

    1. Disconnect the connector (E38) from the air conditioning amplifier.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      E38-11 (CANH) - E38-12 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      54 to 69 Ω
      E38-11 (CANH) - E38-14 (GND)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      E38-12 (CANL) - E38-14 (GND)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      E38-11 (CANH) - E38-21 (B)
      B - GR
      HIGH-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher
      E38-12 (CANL) - E38-21 (B)
      W - GR
      LOW-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher


COMBINATION METER ECU (2GR-FE)
  1. Disconnect the F1 connector from the combination meter.

  2. C133254E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    Ignition Switch off
    108 to 132 Ω

  3. C133255E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    F1-17 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-18 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-17 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    F1-18 (CANL) - F1-2 (B2)
    B - R
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


COMBINATION METER ECU (2AZ-FE)
  1. Disconnect the F1 connector from the combination meter.

  2. C133254E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Condition
    F1-23 (CANH) - F1-22 (CANL)
    Ignition Switch off
    108 to 132 Ω

  3. C133255E06
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-23 (CANH) - F1-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    F1-23 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-22 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-23 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    F1-22 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


MAIN BODY ECU (INSTRUMENT PANEL J/B)

  1. C136714E02
    Disconnect the E8 main body ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-5 (CANH) - E8-6 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω

  3. Measure the resistance according to the value(s) in the table below.
    C142736E01

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    E8-5 (CANH) - E8-6 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition switch off
    54 to 69 Ω
    E8-5 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E8-6 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E8-5 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    E8-6 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    E8-16 (CANP)* - E8-15 (CANN)*
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition switch off
    108 to 132 Ω
    E8-16 (CANP)* - E10-4 (CG)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E8-15 (CANN)* - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    E8-16 (CANP)* - E10-16 (BAT)
    L - L
    HIGH-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    E8-15 (CANN)* - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher

    *: with Clearance sonar system (w/ corner sensor)


CLEARANCE WARNING ECU (w/ CLEARANCE SONAR SYSTEM (w/ CORNER SENSOR))

  1. C142212E03
    Disconnect the connector from the clearance warning ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Value
    O30-3 (R1) - O30-5 (R2)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition switch off
    54 to 69 Ω
    O30-3 (R1) - O30-17 (E)
    L - W-B
    HIGH-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    O30-5 (R2) - O30-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition switch off
    200 Ω or higher
    O30-3 (R1) - E10-16 (BAT)
    L - L
    HIGH-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher
    O30-5 (R2) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition switch off
    6 kΩ or higher

← PROBLEM SYMPTOMS TABLE (from Jun 2009)TERMINALS OF ECU (from Jun 2009) →