2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Oct 2006

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR (NO. 1 CAN J/C, NO. 2 CAN J/C)

  1. No. 1 CAN J/C
    C144992E02

    No. 1 CAN J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    CAN Main Bus Wire (E42)
    White
    B
    W
    Center Airbag Sensor Assembly (E45)
    Black
    B
    W
    No. 1 CAN J/C connectors ("B" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    DLC3 (E62)
    White*1
    Gray*2
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    *1: 2GR-FE
    *2: 2AZ-FE

  2. No. 4 CAN J/C (REAR OF THE VEHICLE)
    C137762E19

    Terminals
    Wiring Color
    Connects to
    A40-1 (CANH)
    B
    ECM (CANH)
    A40-7 (CANL)
    W
    ECM (CANL)
    A40-2 (CANH)
    B
    Skid Control ECU (CANH)
    A40-8 (CANL)
    W
    Skid Control ECU (CANL)

  3. No. 4 CAN J/C (FRONT OF THE VEHICLE)
    C137763E10

    Terminals
    Wiring Color
    Connects to
    E41-1 (CANH)
    B
    A/C Amplifier (CANH)
    E41-7 (CANL)
    W
    A/C Amplifier (CANL)
    E41-4 (CANH)
    B
    No. 1 CAN J/C (CANH)
    E41-10 (CANL)
    W
    No. 1 CAN J/C (CANL)

  4. The connection diagram of the components which are connected to the CAN J/C
    C144959E02


DLC3

  1. C125062E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E10-6 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E10-6 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


SKID CONTROL ECU
  1. Disconnect the A25 connector from the skid control ECU.

  2. C131970E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-26 (CANH) - A25-15 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    A25-26 (CANH) - A25-4 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A25-15 (CANL) - A25-4 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A25-26 (CANH) - A25-3 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    A25-15 (CANL) - A25-3 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY
  1. Disconnect the E30 connector from the center airbag sensor assembly.

  2. C125063E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E30-13 (CANH) - E30-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E30-13 (CANH) - E30-25 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E30-22 (CANL) - E30-25 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E30-13 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    E30-22 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


ECM

  1. 2AZ-FE
    A107881E28

    1. Disconnect the A24 connector from the ECM.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Terminals
      Condition
      Specified Condition
      A24-41 (CANH) - A24-49 (CANL)
      Ignition Switch off
      108 to 132 Ω

    3. C136709E05
      Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      A24-41 (CANH) - A24-49 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      108 to 132 Ω
      A24-41 (CANH) - C24-104 (E1)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A24-49 (CANL) - C24-104 (E1)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A24-41 (CANH) - A24-20 (BATT)
      B - Y
      HIGH-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher
      A24-49 (CANL) - A24-20 (BATT)
      W - Y
      LOW-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher

  2. 2GR-FE
    A107881E23

    1. Disconnect the A55 connector from the ECM.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Terminals
      Condition
      Specified Condition
      A55-41 (CANH) - A55-49 (CANL)
      Ignition Switch off
      108 to 132 Ω

    3. C136709E06
      Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      A55-41 (CANH) - A55-49 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      108 to 132 Ω
      A55-41 (CANH) - C55-81 (E1)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A55-49 (CANL) - C55-81 (E1)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A55-41 (CANH) - A55-20 (BATT)
      B - Y
      HIGH-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher
      A55-49 (CANL) - A55-20 (BATT)
      W - Y
      LOW-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher


AIR CONDITIONING AMPLIFIER

  1. E124470E20
    Check the harness side connector (E38) of the air conditioning amplifier.

    1. Disconnect the connector (E38) from the air conditioning amplifier.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      E38-11 (CANH) - E38-12 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      54 to 69 Ω
      E38-11 (CANH) - E38-14 (GND)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      E38-12 (CANL) - E38-14 (GND)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      E38-11 (CANH) - E38-21 (B)
      B - GR
      HIGH-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher
      E38-12 (CANL) - E38-21 (B)
      W - GR
      LOW-level CAN bus wire - Battery positive
      Ignition Switch off
      6 kΩ or higher


COMBINATION METER ECU (2GR-FE)
  1. Disconnect the F1 connector from the combination meter.

  2. C133254E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    Ignition Switch off
    108 to 132 Ω

  3. C133255E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    F1-17 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-18 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-17 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    F1-18 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


COMBINATION METER ECU (2AZ-FE)
  1. Disconnect the F1 connector from the combination meter.

  2. C133254E05
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Condition
    Specified Condition
    F1-23 (CANH) - F1-22 (CANL)
    Ignition Switch off
    108 to 132 Ω

  3. C133255E06
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-23 (CANH) - F1-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    F1-23 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-22 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-23 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher
    F1-22 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Ignition Switch off
    6 kΩ or higher


MAIN BODY ECU (INSTRUMENT PANEL J/B)
  1. Disconnect the E8 connector from the main body ECU.

  2. C136714E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-5 (CANH) - E8-6 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E8-16 (CANP) - E8-15 (CANN)
    L - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω

← PROBLEM SYMPTOMS TABLE (from Jun 2009)DIAGNOSIS SYSTEM (Oct 2006 – May 2009) →