2006-2011 Camry Aurion · Service Manual STEERING

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


DESCRIPTION
  1. DIAGNOSTIC SYSTEM
    When troubleshooting a vehicle with a diagnostic system, the only difference from the usual troubleshooting procedure is connecting the intelligent tester to the vehicle and reading various data output from the vehicle's steering lock ECU.
    The steering lock ECU records DTCs when the computer detects a malfunction in the computer itself or in system circuits.
    To check the DTCs, connect the intelligent tester to the DLC3 on the vehicle. The intelligent tester enables the DTCs to be cleared, the indicators to be activated, and the DATA LIST to be checked.

  2. The steering lock ECU diagnosis information cannot be read directly from the steering lock ECU by the tester. The diagnosis information from the steering lock ECU is transmitted to the tester via the certification ECU to the tester using the controller area network (CAN).


CHECK DLC3

  1. H100769E16
    The certification ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.
    Symbols (Terminal No.)
    Terminal Description
    Condition
    Specified Condition
    SIL (7) - SG (5)
    Bus "+" line
    During transmission
    Pulse generation
    CG (4) - Body ground
    Chassis ground
    Always
    Below 1 Ω
    SG (5) - Body ground
    Signal ground
    Always
    Below 1 Ω
    BAT (16) - Body ground
    Battery positive
    Always
    11 to 14 V
    CANH (6) - CANL (14)
    CAN bus line
    Engine Switch off*
    54 to 69 Ω
    CANH (6) - CG (4)
    HIGH-level CAN bus line
    Engine Switch off*
    200 Ω or higher
    CANL (14) - CG (4)
    LOW-level CAN bus line
    Engine Switch off*
    200 Ω or higher
    CANH (6) - BAT (16)
    HIGH-level CAN bus line
    Engine Switch off*
    6 kΩ or higher
    CANL (14) - BAT (16)
    LOW-level CAN bus line
    Engine Switch off*
    6 kΩ or higher

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches or the doors.

    If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

  2. A132338E01
    Connect the cable of the intelligent tester to the DLC3, turn the engine switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
    1. If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
    2. If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.


WARNING FUNCTION OF ENGINE SWITCH INDICATOR

  1. B083100E01
    The steering lock ECU blinks the LED indicator of the engine switch when any of the following problems occurs in the system:
    Detection Item
    Indicator Light Blink Pattern
    Indication Status
    Countermeasure
    Steering lock is still not released
    1. Blinks green at 1-second intervals
    2. Goes off 15 seconds after blinking starts
    The motor operates to release the steering lock, but the steering lock cannot be released (e.g. the lock bar is stuck in the steering column).
    Push the engine switch while turning the steering wheel left or right.
    Malfunction in smart entry and start system
    1. Blinks amber at 2-second intervals
    2. Goes off 15 seconds after the engine switch is turned off while blinking
    1. There is a short in the devices activating the motor.
    2. There is a problem in the steering lock ECU or main body ECU.
    Troubleshoot by following "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).


WARNING FUNCTION OF COMBINATION METER
  1. The steering lock ECU displays a warning on the combination meter when any of the following problems occurs in the system.

    Detection Item
    Display
    Indication Status
    Countermeasure
    Steering lock is still not released
    "S/T IS NOT UNLOCKED"
    1. Goes off 15 seconds after blinking starts
    The motor operates to release the steering lock, but the steering lock cannot be released (e.g. the lock bar is stuck in the steering column).
    Push the engine switch while turning the steering wheel left or right.
    Malfunction in smart entry and start system
    "CHECK S/T LOCK"
    1. Goes off 15 seconds after the engine switch is turned off while blinking
    1. There is a short in the devices activating the motor.
    2. There is a problem in the steering lock ECU or main body ECU.
    Troubleshoot by following "HOW TO PROCEED WITH TROUBLESHOOTING" (Click here).

← TERMINALS OF ECU (from Jun 2009)DIAGNOSIS SYSTEM (from Jun 2009) →