REMOVAL
Removal / installation · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 2.
REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)
|
 |
- Put protective tape around the front bumper assembly.
- Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
- HINT:
- Use the same procedure for the RH side and LH side.
- Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
- Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
- HINT:
- Use the same procedure for the RH side and LH side.
Remove the front bumper assembly.
| 3.
REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)
|
 |
- Put protective tape around the front bumper assembly.
- Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
- HINT:
- Use the same procedure for the RH side and LH side.
- Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
- Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
- HINT:
- Use the same procedure for the RH side and LH side.
Disconnect each connector, and then remove the front bumper assembly.
| 4.
REMOVE FRONT FENDER LINER (w/o Front Fender Mudguard) |
 |
- Remove the 5 clips and bolt.
Remove the 5 screws, grommet and the front fender liner.
- HINT:
- The grommet will break when it is removed. Replace the old grommet with a new one.
| 5.
REMOVE FRONT FENDER MUDGUARD SUB-ASSEMBLY (w/ Front Fender Mudguard)
|
 |
- Remove the 3 screws and front fender mudguard sub-assembly.
| 6.
REMOVE FRONT FENDER LINER (w/ Front Fender Mudguard) |
 |
- Remove the 4 clips and bolt.
Remove the 3 screws, grommet and the front fender liner.
- HINT:
- The grommet will break when it is removed. Replace the old grommet with a new one.
| 7.
REMOVE HIGH PITCHED HORN ASSEMBLY (for LHD)
|
 |
- Disconnect the connector.
Remove the bolt and the high pitched horn assembly.
| 8.
REMOVE LOW PITCHED HORN ASSEMBLY (for RHD)
|
 |
- Disconnect the connector.
Remove the bolt and the low pitched horn assembly.
| 9.
REMOVE HOOD LOCK ASSEMBLY (for LHD) |
 |
- Remove the 3 bolts.
- Disconnect the hood lock control cable.
Remove the hood lock assembly.
| 10.
REMOVE HOOD LOCK ASSEMBLY (for RHD) |
 |
- Disconnect the connector.
Remove the 3 bolts.
- Disconnect the hood lock control cable.
Remove the hood lock assembly.
| 11.
REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD) |
 |
- Disconnect the hood lock control cable and remove the hood lock control lever.
| 12.
REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD) |
 |
- Disconnect the hood lock control cable and remove the hood lock control lever.
| 13.
REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD) |
 |
Using a screwdriver, disconnect the clamps shown in the illustration.


Area
|
Part Name
|
Area
|
Part Name
|
A
|
Hood lock control cable
|
G
|
Hood lock protector
|
B
|
Clamp
|
H
|
Grommet
|
C
|
Wire harness
|
I
|
Side member outer
|
D
|
Pillar
|
J
|
Radiator
|
E
|
Nut
|
K
|
Front fender apron
|
F
|
Radiator support upper
|
L
|
Brace
|
- HINT:
- Tape the screwdriver tip before use.
Pull the cable from the engine compartment and remove it.
| 14.
REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD) |
 |
Using a screwdriver, disconnect the clamps shown in the illustration.


Area
|
Part Name
|
Area
|
Part Name
|
A
|
Hood lock control cable
|
G
|
Side member outer
|
B
|
Clamp
|
H
|
Radiator
|
C
|
Washer hose
|
I
|
Front fender apron
|
D
|
Radiator support upper
|
J
|
Brace
|
E
|
Hood lock protector
|
K
|
Pillar
|
F
|
Grommet
|
-
|
-
|
- HINT:
- Tape the screwdriver tip before use.
Pull the cable from the engine compartment and remove it.