2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. REMOVE FRONT WHEEL

2. REMOVE COOL AIR INTAKE DUCT SEAL

  1. B232362
    Remove the 7 clips and cool air intake duct seal.


3. REMOVE FRONT BUMPER ASSEMBLY

  1. B232367E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B232368
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B232369
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. w/ Clearance Sonar System:

    1. Disconnect the 2 connectors.

  1. w/ Fog Light:

    1. Disconnect the 2 connectors.

  1. w/ Headlight Cleaner System:

    1. Disconnect the 2 connectors.

    2. B149621
      Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.

  1. Remove the front bumper assembly.


4. REMOVE FRONT FENDER LINER (w/o Front Fender Mudguard)

  1. B149004
    Remove the 5 clips and bolt.

  1. Remove the 5 screws, grommet and the front fender liner.

    HINT:
    The grommet needs to be replaced with a new one because it will break when it is removed.


5. REMOVE FRONT FENDER MUDGUARD SUB-ASSEMBLY (w/ Front Fender Mudguard)

  1. B165397
    Remove the 3 screws and front fender mudguard sub-assembly.


6. REMOVE FRONT FENDER LINER (w/ Front Fender Mudguard)

  1. B141646
    Remove the 4 clips and bolt.

  1. Remove the 3 screws, grommet and the front fender liner.

    HINT:
    The grommet needs to be replaced with a new one because it will break when it is removed.


7. REMOVE HIGH PITCHED HORN ASSEMBLY (for LHD)

  1. E136738
    Disconnect the connector.

  1. Remove the bolt and the high pitched horn assembly.


8. REMOVE LOW PITCHED HORN ASSEMBLY (for RHD)

  1. E136739
    Disconnect the connector.

  1. Remove the bolt and the low pitched horn assembly.


9. REMOVE HOOD LOCK ASSEMBLY (for LHD)

  1. B159067
    Remove the 3 bolts.

  1. B149001
    Disconnect the hood lock control cable.

  1. Remove the hood lock assembly.


10. REMOVE HOOD LOCK ASSEMBLY (for RHD)

  1. B155583
    Disconnect the connector.

  1. Remove the 3 bolts.

  1. B155584
    Disconnect the hood lock control cable.

  1. Remove the hood lock assembly.


11. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)

  1. B136909
    Disconnect the hood lock control cable and remove the hood lock control lever.


12. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD)

  1. B140442
    Disconnect the hood lock control cable and remove the hood lock control lever.


13. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)

  1. Using a screwdriver, disconnect the clamps shown in the illustration.

    B168292E01

    Area
    Part Name
    Area
    Part Name
    A
    Hood lock control cable
    G
    Hood lock protector
    B
    Clamp
    H
    Grommet
    C
    Wire harness
    I
    Side member outer
    D
    Pillar
    J
    Radiator
    E
    Nut
    K
    Front fender apron
    F
    Radiator support upper
    L
    Brace

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the cable from the engine compartment and remove it.


14. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)

  1. Using a screwdriver, disconnect the clamps shown in the illustration.

    B159068E01

    Area
    Part Name
    Area
    Part Name
    A
    Hood lock control cable
    G
    Side member outer
    B
    Clamp
    H
    Radiator
    C
    Washer hose
    I
    Front fender apron
    D
    Radiator support upper
    J
    Brace
    E
    Hood lock protector
    K
    Pillar
    F
    Grommet
    -
    -

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the cable from the engine compartment and remove it.

← REMOVAL (Oct 2006 – May 2009)INSTALLATION (Oct 2006 – May 2009) →