2006-2011 Camry Aurion · Service Manual ENGINE

PRECAUTION

Precautions · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


1.PRECAUTION
  1. Before inspecting and repairing the fuel system, disconnect the cable from the negative battery terminal.

  2. Do not smoke or work near fire when handling the fuel system.

  3. Keep gasoline away from rubber or leather parts.


2.Expressions of ignition switch
  1. The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.

    Switch Type
    Ignition Switch
    (Position)
    Engine Switch
    (Condition)
    Expression
    Ignition switch off
    LOCK
    Off
    Ignition switch on (IG)
    ON
    On (IG)
    Ignition switch on (ACC)
    ACC
    On (ACC)
    Engine start
    START
    Start


3.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Perform the following procedures to prevent fuel from spilling out before removing any fuel system parts.
  2. Pressure will still remain in the fuel line even after performing the following procedures. When disconnecting the fuel line, cover it with a shop rag or a piece of cloth to prevent fuel from spraying or coming out.

  1. Remove the rear seat cushion assembly.
    for fold down seat type: Click here
    for fixed type: Click here

  2. A129607
    Remove the rear floor service hole cover.

  3. Disconnect the fuel pump connector.

  4. Start the engine.

  5. After the engine stops, turn the ignition switch off.

    HINT:
    DTC P0171/25 (fuel problem) may be detected.

  6. Crank the engine again. Check that the engine does not start.

  7. Remove the fuel tank cap to discharge pressure from the fuel tank.

  8. Disconnect the cable from the negative battery terminal.

  9. Reconnect the fuel pump connector.

  10. Install the rear floor service hole cover.

  11. Install the rear seat.


4.FUEL SYSTEM

  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out, so observe the following procedures:

    1. Discharge the fuel system pressure (step 2).

    2. Disconnect the fuel tube (Click here).

    3. Drain the fuel that remains inside the fuel tube.

    4. B000679E07
      To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.

    5. Put a container under the connection part.

  2. A131629E01
    Observe the following precautions when removing and installing the fuel injectors:

    1. Never reuse an O-ring.

    2. When placing a new O-ring on the injector, do not damage the O-ring.

    3. Coat a new O-ring with gasoline before installing it.

      NOTICE:
      Do not use engine oil, gear oil or brake fluid.

  3. A097444E03
    Install the injector to the delivery pipe and cylinder head, as shown in the illustration.

    NOTICE:
    Before installing the injector, be sure to apply grease or gasoline to the place where the delivery pipe or cylinder head contacts the O-ring of the injector.

  4. A050709E04
    Observe the following precautions when disconnecting the fuel delivery pipe (metallic type):

    HINT:
    The structure of the metallic connector is shown on the left.


    1. A136248E01
      Remove the No. 2 fuel pipe clamp.

      HINT:
      The No. 2 fuel pipe clamp cannot be reused.

    2. A130371E01
      Find the metallic connector of the fuel tube assembly.

    3. Assemble SST to the connection as shown in the illustration.

      SST
      09268-21011  

    4. Turn the SST, align the retainers inside the connector with the SST chamfered parts and insert SST into the connector.

    5. Slide the SST and the connector together towards the fuel tube assembly.

  5. Observe the following precautions when connecting the fuel tube connector (metallic type):

    1. Check if there is any damage or foreign objects on the connecting part of the pipe.

    2. Match the axis of the connector with the axis of the pipe, and push into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.

    3. A142841E01
      After finishing the connection, check if the pipe and the connector are securely connected by pulling on them.

    4. Check for fuel leaks.

    5. A136248E02
      Install a new No. 2 fuel pipe clamp.

  6. Observe the following precautions when disconnecting the fuel tube connectors (Quick type A):

    1. A060083E16
      Remove the No. 1 fuel pipe clamp from the tube connector.

    2. Check that there is no dirt or other foreign objects on the pipe and around the connector before disconnecting them. Clean them if necessary.

    3. A088336E16
      Disconnect the connector from the pipe by hand.

    4. When the connector and the pipe are stuck, push in and pull on the connector to release it. Pull the connector out of the pipe carefully.

    5. Check that there is no dirt or other foreign objects on the sealing surface of the disconnected pipe. Clean it away if necessary.

    6. B009222E07
      Do not damage the disconnected pipe and connector, and prevent entry of foreign objects by covering them with plastic bags.

  7. Observe the following precautions when connecting the fuel tube connectors (Quick Type A):

    1. Check if there is any damage or foreign objects on the connecting parts of the pipes.

    2. Line up the two parts of the pipes to be connected, and push them together until the connector makes a "click" sound. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.

    3. A121423E02
      After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.

    4. Check for fuel leaks.

  8. A129459E01
    Observe the following precautions when disconnecting the fuel tube connector (Quick type B):

    1. Before disconnecting the connector, clean off any dirt that may be present.

    2. Pinch the tabs of the fuel tube retainer to disengage the 2 claws. Push the retainer down as shown in the illustration.

      HINT:
      Be sure to disconnect the connector by hand.

    3. A091246E06
      If the connector and pipe are stuck, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.

    4. If there is any dirt or any other foreign objects on the sealing surfaces of the disconnected pipes, clean them if necessary.

    5. A093309E03
      Do not damage the disconnected pipe and connector, and prevent entry of foreign objects by covering them with plastic bags.

  9. Observe the following precautions when connecting the fuel tube connector (Quick Type B):

    1. A132390E01
      Line up the two parts of the pipes to be connected, and fully push the fuel tube connector and pipe together until they are fully seated. Next, push the retainer into the connector until its claws lock. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.

    2. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.

    3. Check for fuel leaks.

  10. Observe the following precautions when handling a nylon tube:

    CAUTION:
    1. Do not twist the connection part of the nylon tube and the quick connector when connecting them.
    2. Do not bend or twist the nylon tube.
    3. Do not remove the EPDM protector on the outside of the nylon tube.
    4. Do not close the piping by bending the nylon tube.


5.INSPECT FOR FUEL LEAK
  1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs (Click here).

← PRECAUTION (Jun 2006 – May 2009)PARTS LOCATION (from Jun 2006) →