2006-2011 Camry Aurion · Service Manual ENGINE

B2286 Runnable Signal Malfunction

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This DTC is output when serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM are inconsistent.

HINT:
When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2286
Serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM are inconsistent.
  1. CAN communication system
  2. ECM
  3. Main body ECU
  4. Wire harness or connector

WIRING DIAGRAM

B157548E01

INSPECTION PROCEDURE


1. CHECK OPERATION OF TACHOMETER
  1. Run the engine and check if the function of the tachometer in the combination meter is normal.

    OK:
    Actual engine revolution speed and the revolution indicated on the tachometer are the same.



NG
Go to step 3
OK


2. CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
  1. Delete the DTCs (Click here).

  1. Check for CAN communication system DTC (for LHD: Click here), (for RHD: Click here).

    HINT:
    If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (for LHD: Click here), (for RHD: Click here).

    OK:
    No DTC is output.



NG
GO TO CAN COMMUNICATION SYSTEM
OK

GO TO COMBINATION METER SYSTEM

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)

  1. Disconnect the A55*1 or A24*2 ECM connector.B157566E01

  1. Disconnect the E8 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-8 (TACH) - A55-15 (TACH)*1
    E8-8 (TACH) - A24-15 (TACH)*2
    Always
    Below 1 Ω
    E8-8 (TACH) or A55-15 (TACH) - Body ground*1
    E8-8 (TACH) or A24-15 (TACH) - Body ground*2
    Always
    10 kΩ or higher

    HINT:
    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. READ VALUE USING INTELLIGENT TESTER
  1. Reconnect the connectors.

  1. Connect the intelligent tester to the DLC3.

  1. Check the DATA LIST for proper functioning of the engine.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    E/G Cond
    Engine condition/STOP or RUN
    STOP: Engine is stopped
    RUN: Engine is running
    -

    OK:
    STOP (engine is stopped) and RUN (engine is running) appear on the screen.



NG
REPLACE ECM (Click here)
OK

REPLACE MAIN BODY ECU


← B2285 Steering Lock Position Signal Circuit Malfunction (from Jun 2009)B2286 Runnable Signal Malfunction (from Jun 2009) →