2006-2011 Camry Aurion · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

  1. A128158
    Remove the oil filler cap.


2. REMOVE OIL FILLER CAP GASKET

  1. A128159
    Remove the oil filler cap gasket.


3. REMOVE VENTILATION VALVE SUB-ASSEMBLY

  1. A128160
    Remove the ventilation valve.


4. REMOVE SPARK PLUG

  1. A128161
    Remove the spark plugs.


5. REMOVE OIL FILTER SUB-ASSEMBLY

  1. A036541E01
    Using SST, remove the oil filter.
    SST
    09228-06501  

    HINT:
    Place a container for oil to be drained before removing the oil filter.


6. REMOVE OIL COOLER ASSEMBLY

  1. A135533
    Remove the oil filter union, plate washer, nut, oil cooler and O-ring.

  1. Remove the union bolt.


7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A112210E01
    Remove the 2 bolts and disconnect the 2 engine wires.

  1. A127550E02
    Remove the 8 bolts, 2 nuts, and the cylinder head cover.


8. REMOVE CYLINDER HEAD COVER GASKET

  1. A144061
    Remove the cylinder head cover gasket.


9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A112212
    Remove the bolt, nut and belt tensioner.


10. REMOVE CRANKSHAFT POSITION SENSOR

  1. A094516E01
    Remove the wire harness clamp.

  1. Separate the wire harness from the wire harness clamp bracket.

  1. A063828
    Remove the 2 bolts and sensor.


11. REMOVE CAMSHAFT POSITION SENSOR

  1. A128164
    Remove the bolt and sensor.


12. REMOVE CRANKSHAFT PULLEY

  1. A013697E02
    Using SST, hold the pulley in place and loosen the pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A124860E01
    Using SST, remove the pulley bolt and pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-40011   (09957-04010)

    HINT:
    If necessary, remove the pulley and pulley bolt using SST.


13. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A124556
    Disconnect the camshaft timing oil control valve assembly connector.

  1. Remove the bolt and camshaft timing oil control valve assembly.


14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098348E01
    Remove the 2 nuts, tensioner and gasket.

    NOTICE:
    Do not turn the crankshaft without the chain tensioner.


15. REMOVE WATER PUMP PULLEY

A098715E03
  1. Using SST, remove the 4 bolts and water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)


16. REMOVE WATER PUMP ASSEMBLY

A094516E01
  1. Remove the clamp of the crankshaft position sensor from the water pump.

  1. Disconnect the wire of the crankshaft position sensor from the clamp bracket.

  1. B012052E03
    Remove the 4 bolts, 2 nuts and clamp bracket.

  1. A129792
    Using a screwdriver, pry between the water pump and cylinder block, and then remove the water pump.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the water pump and cylinder block.


17. REMOVE OIL PAN DRAIN PLUG

  1. A128176
    Remove the oil pan drain plug and gasket.


18. REMOVE OIL PAN SUB-ASSEMBLY

  1. A114333
    Remove the 12 bolts and 2 nuts.

  1. A000019E05
    Insert the blade of SST between the crankcase and oil pan. Cut through the sealer and remove the oil pan.
    SST
    09032-00100  

    NOTICE:
    Be careful not to damage the contact surfaces of the crankcase, chain cover and oil pan.


19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A128178
    Using a E10 "torx" socket, remove the stud bolt for the drive belt tensioner from the cylinder block.

  1. Remove the 12 bolts and 2 nuts.

  1. A128179
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

    HINT:
    Tape the screwdriver tip before use.


20. REMOVE TIMING CHAIN CASE OIL SEAL

  1. A128180
    Using a screwdriver and a hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


21. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A132571
    Remove the crankshaft position sensor plate.


22. REMOVE TIMING CHAIN GUIDE

  1. A125373
    Remove the bolt and timing chain guide.


23. REMOVE CHAIN TENSIONER SLIPPER

  1. A125372
    Remove the bolt and chain tensioner slipper.


24. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A125371
    Remove the 2 bolts and chain vibration damper.


25. REMOVE CHAIN SUB-ASSEMBLY

  1. A128185
    Remove the chain sub-assembly.


26. REMOVE CRANKSHAFT TIMING SPROCKET

  1. A125374
    Remove the crankshaft timing sprocket.


27. REMOVE NO. 2 CHAIN SUB-ASSEMBLY

  1. A098351E01
    Turn the crankshaft 90° counterclockwise to align the adjusting hole of the oil pump drive shaft gear with the groove of the oil pump.

  1. A098352E01
    Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then remove the nut.

  1. B011415E03
    Remove the bolt, chain tensioner plate and spring.

  1. A063847
    Remove the chain tensioner, oil pump drive shaft gear, oil pump drive gear and chain.


28. REMOVE KEYS

  1. A131498
    Remove the 2 pulley set keys from the crankshaft.


29. REMOVE NO. 2 CAMSHAFT

  1. A098174E11
    Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.


30. REMOVE CAMSHAFT

  1. A098175E04
    Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.


31. REMOVE NO. 1 CAMSHAFT BEARING

  1. A128191
    Remove the No. 1 camshaft bearing.


32. REMOVE NO. 2 CAMSHAFT BEARING

  1. A032664
    Remove the No. 2 camshaft bearing.


33. REMOVE CAMSHAFT TIMING SPROCKET

  1. A032167
    Clamp the camshaft in a vise.

  1. Remove the flange bolt of the camshaft timing sprocket.


34. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

  1. A090848E03
    Clamp the camshaft in a vise, and make sure that the camshaft timing gear does not rotate.

  1. Cover all the oil ports except the advance side port shown in the illustration with vinyl tape.

  1. A031032
    Apply air pressure of 100 kPa (1.0 kgf/cm2, 14 psi) to the oil path, then turn the camshaft timing gear in the advance direction (counterclockwise) by hand.

    CAUTION:
    Cover the paths with a shop rag or piece of cloth to keep oil from splashing.

    HINT:
    Depending on the air pressure, the camshaft timing gear will turn to the advance angle side without applying force by hand. Also, if the pressure is difficult to apply because of air leakage from the port, the lock may be difficult to release.

  1. A032639
    Remove the flange bolt of the camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If the gear is to be reused, be sure to release the straight pin lock before installing the gear.


35. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. F050595E04
    Using several steps, uniformly loosen and remove the 10 cylinder head set bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.

    NOTICE:
    Head warpage or cracking could result from removing the bolts in the wrong order.

  1. A126930
    Using a screwdriver with its tip wrapped with tape, pry between the cylinder head and cylinder block, and remove the cylinder head.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.


36. REMOVE CYLINDER HEAD GASKET

  1. A126929
    Remove the cylinder head gasket.


37. REMOVE OIL CONTROL VALVE FILTER

  1. A128210E01
    Using an 8 mm socket hexagon wrench, remove the plug and filter.


38. REMOVE OIL PUMP ASSEMBLY

  1. A128253
    Remove the 3 bolts, oil pump and gasket.


39. REMOVE NO. 1 AND NO. 2 BALANCESHAFT SUB-ASSEMBLY

  1. A128197E01
    Uniformly loosen and remove the 8 bolts in the sequence shown in the illustration.

  1. A128203E02
    Remove the No. 1 and No. 2 balanceshafts.


40. REMOVE NO. 1 BALANCESHAFT BEARING

  1. A128204E02
    Remove the balanceshaft bearings.


41. REMOVE ENGINE REAR OIL SEAL

  1. A128201E02
    Using a knife, cut off the oil seal lip.

  1. Using a screwdriver with its tip taped, pry out the oil seal.

    NOTICE:
    After removing the oil seal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.


42. REMOVE STIFFENING CRANKCASE ASSEMBLY

  1. A128202E02
    Uniformly loosen and remove the 11 bolts in the sequence shown in the illustration.

  1. A128205E01
    Using a screwdriver, remove the crankcase by prying between the crankcase and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the crankcase and cylinder block.

  1. A128206
    Remove the O-ring from the cylinder block.


43. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

  1. A013469
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. A063893E01
    Check that the matchmarks on the connecting rod and cap are aligned to ensure correct reassembly.

    HINT:
    The matchmarks on the connecting rods and caps are provided to ensure correct reassembly.

  1. A013397
    Using a 12 mm socket wrench, uniformly loosen the 2 bolts.

  1. Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted in the connecting rod cap.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


44. REMOVE CONNECTING ROD BEARING
  1. Remove the connecting rod bearings.

    HINT:
    Arrange the removed parts in the correct order.


45. REMOVE PISTON RING SET

  1. A128232E01
    Using a piston ring expander, remove the 2 compression rings.

  1. Remove the oil ring rail and oil ring expander by hand.

    HINT:
    Arrange the removed parts in the correct order.


46. REMOVE PISTON PIN HOLE SNAP RING

  1. A128233
    Using a screwdriver, pry out the 2 snap rings.


47. REMOVE PISTON

  1. A109729
    Gradually heat each piston to approximately 80 to 90°C (176 to 194°F).

  1. A106279
    Using a plastic hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


48. REMOVE CRANKSHAFT

  1. A128235E01
    Uniformly loosen and remove the 10 main bearing cap bolts in the sequence shown in the illustration.

  1. A087781
    Use 2 removed main bearing cap bolts to remove the 5 main bearing caps and 5 lower bearings.

    NOTICE:
    Insert the bolts into the caps in turn. Ease the cap out by gently pulling up and applying force toward the front and back sides of the cylinder block, as shown in the illustration. Take care not to damage the contact surfaces of the cap and cylinder block.

    HINT:
    1. Keep the lower bearing and main bearing cap together.
    2. Arrange the main bearing caps in the correct order.

  1. Lift out the crankshaft.


49. REMOVE UPPER CRANKSHAFT THRUST WASHER

  1. A013501E04
    Remove the upper crankshaft thrust washers from the cylinder block.


50. REMOVE CRANKSHAFT BEARING

  1. A063901
    Remove the 5 upper main bearings from the cylinder block.

    HINT:
    Arrange the bearings in the correct order.


51. REMOVE NO. 2 CRANKSHAFT BEARING

  1. A063902
    Remove the 5 lower main bearings from the 5 main bearing caps.

    HINT:
    Arrange the bearings in the correct order.


52. REMOVE STUD BOLT

53. CLEAN CYLINDER BLOCK

NOTICE:
If the cylinder is washed at high temperatures, the cylinder liner will stick out beyond the cylinder block. Always wash the cylinder block at a temperature of 45°C (113°F) or less.

← DISASSEMBLY (Jun 2006 – Sep 2006)DISASSEMBLY (from Jun 2009) →