Install the stud bolts as shown in the illustration.
Torque:
Stud Bolt A:
22 N*m{
220 kgf*cm
, 16 ft.*lbf
}
Stud Bolt B:
5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
Stud Bolt C:
9.5 N*m{
97 kgf*cm
, 84 in.*lbf
}
Stud Bolt D:
5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
3.
INSTALL STRAIGHT PIN
Using a plastic hammer, tap in the straight pin.
Standard protrusion:
Item
Protrusion
Pin A
8 mm (0.315 in.)
Pin B
7.5 mm (0.295 in.)
Pin C
12 mm (0.472 in.)
Pin D
5 mm (0.197 in.)
4.
INSTALL PISTON
Using a screwdriver, install a new snap ring at one end of the piston pin hole.
HINT:
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
Align the front marks of the piston and connecting rod, and push in the piston with your thumb.
Using a screwdriver, install a new snap ring on the other end of the piston pin hole.
HINT:
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
5.
INSTALL PISTON RING SET
Install the oil ring expander and 2 oil ring rails by hand.
Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.
NOTICE:
Install the compression ring No. 2 with the code mark (2N or 2R) facing upward.
Position the piston rings so that the ring ends are as shown in the illustration.
6.
INSTALL CRANKSHAFT BEARING
Install the upper bearing with an oil groove on the cylinder block.
NOTICE:
Do not apply engine oil to the bearings and the contact surfaces.
7.
INSTALL NO. 2 CRANKSHAFT BEARING
Install the lower bearing onto the bearing cap.
NOTICE:
Clean the backside of the bearing and the bearing surface of the connecting rod. The surface should be free of dust and oil.
8.
INSTALL UPPER CRANKSHAFT THRUST WASHER
Install the 2 thrust washers under the No. 3 journal of the cylinder block with the oil grooves facing outward.
Apply engine oil to the crankshaft thrust washer.
9.
INSTALL CRANKSHAFT
Apply engine oil to the upper bearing and install the crankshaft on the cylinder block.
Apply engine oil to the lower bearing.
Examine the front marks and install the bearing caps on the cylinder block.
Apply a light coat of engine oil to the threads and under the bearing cap bolts.
Install the crankshaft bearing cap bolts.
NOTICE:
The main bearing cap bolts are tightened in 2 progressive steps.
Step 1
Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.
Torque:
20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
Further tighten the 10 main bearing cap bolts in the sequence shown in the illustration.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
Step 2
Mark the front of the bearing cap bolts with paint.
Further tighten the bearing cap bolts by 90° in the numerical order shown in the previous illustration.
Check that the paint mark is now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Check the crankshaft thrust clearance (Click here).
10.
INSTALL CONNECTING ROD BEARING
Align the bearing claw with the groove of the connecting rod or connecting cap.
NOTICE:
Do not apply engine oil to the bearings or the contact surfaces.
11.
INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD
NOTICE:
The connecting rod cap bolts are tightened in 2 progressive steps.
Apply engine oil to the cylinder walls, the pistons, and the surfaces of connecting rod bearings.
Check the position of the piston ring ends.
Using a piston ring compressor, push the correctly numbered piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.
NOTICE:
Match the numbered connecting rod cap with the connecting rod.
Check that the protrusion of the connecting rod cap is facing in the correct direction.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.
Install the connecting cap bolts.
NOTICE:
The connecting cap bolts should be tightened in 2 progressive steps.
Step 1
Install and alternately tighten the bolts of the connecting rod cap in several steps.
Torque:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
Step 2
Mark the front of the connecting rod cap bolts with paint.
Further tighten the cap bolts by 90° as shown in the illustration.
Check that the crankshaft turns smoothly.
Check the connecting rod thrust clearance (Click here).
12.
INSTALL STIFFENING CRANKCASE ASSEMBLY
Place a new O-ring on the cylinder block, as shown in the illustration.
Temporarily tighten the pulley set bolt.
Turn the crankshaft so that the key groove is facing downward.
HINT:
Make sure that the timing mark on the balanceshaft drive gear is positioned as shown in the illustration.
Apply seal packing in a continuous bead (diameter: 2.5 to 3.0 mm (0.098 to 0.118 in.)) to the places shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent
NOTICE:
Remove any oil from the contact surface.
Ensure that no oil packing enters the oil path. The oil path has a groove to catch excess seal packing. Do not apply seal packing to the oil path side of the groove or to the groove itself, or seal packing may enter the oil path.
Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after the installation.
Install the stiffening crankcase assembly to the cylinder block.
Temporarily install the crankcase with the 11 bolts.
Bolt length:
Item
Length
Bolt A
122 mm (4.803 in.)
Bolt B
45 mm (1.772 in.)
Uniformly tighten the 11 bolts in the sequence shown in the illustration.
Torque:
24 N*m{
245 kgf*cm
, 18 ft.*lbf
}
Wipe off any excess seal packing with a clean piece of cloth.
13.
INSTALL NO.1 BALANCESHAFT BEARING
Clean each No.1 balanceshaft bearing installation surface and inner and outer surfaces of the No.1 balanceshaft bearing.
NOTICE:
Do not apply engine oil to the No.1 balanceshaft bearing installation surface or the outer surface of the No.1 balanceshaft bearing.
Align the claw of the No.1 balanceshaft bearing with the groove of the balanshaft housing and install 8 no.1 ballanceshaft bearings.
Apply engine oil to the inner surface of the No.1 balanceshaft bearings.
14.
INSTALL NO. 1 AND NO. 2 BALANCESHAFT SUB-ASSEMBLY
Turn the No.1 driven gear counterclockwise until it stops, then align the matchmark of the No.1 driven gear with that of the No.2 driven gear.
Install the No.1 balanceshaft with the timing mark positioned as shown in illustration. [*1]
HINT:
(A) is not a timing mark.
Install the No.2 balanceshaft with the timing mark positioned as shown in the illustration.
NOTICE:
Make sure that the key groove of the crankshaft and timing mark of the balanceshafts are positioned as shown in the illustration.
HINT:
(A) is not a timing mark.
Apply a light coat of engine oil under the heads of the balanceshaft housing bolts.
Install the balanceshaft housing bolts.
NOTICE:
The balanceshaft housing bolts are tightened in 2 progressive steps.
Step 1
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
Torque:
22 N*m{
220 kgf*cm
, 16 ft.*lbf
}
Step 2
Mark the front side of each balanceshaft housing bolt head with paint.
Further tighten the bolts by 90° as shown in the illustration.
NOTICE:
Check that the paint marks are now at a 90° angle to the front.
Turn the crankshaft 360° and check that the timing marks of the balanceshafts are positioned as shown in the illustraion with the key groove of the crankshaft facing downward.
NOTICE:
If the timing marks are not positioned as shown in the illustration, perform the procedure from step [*1] again.
HINT:
(A) is not a timing mark.
Remove the pulley set bolt.
15.
INSTALL OIL PUMP ASSEMBLY
Install a new gasket and oil pump with the 3 bolts.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
16.
INSTALL ENGINE REAR OIL SEAL
Apply MP grease to a new oil seal lip.
NOTICE:
Wipe off extra grease on the crankshaft.
Using SST and a hammer, evenly tap the oil seal until its surface is flush with the rear oil seal retainer edge.
SST
09223-15030 09950-70010
(09951-07100)
NOTICE:
Keep the lip free from foreign materials.
17.
INSTALL OIL CONTROL VALVE FILTER
Check that no foreign matter is on the mesh part of the filter.
Using an 8 mm socket hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.
Torque:
30 N*m{
306 kgf*cm
, 22 ft.*lbf
}
NOTICE:
Do not touch the mesh when installing the oil control valve filter.
18.
INSTALL CYLINDER HEAD GASKET
Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.
NOTICE:
Remove any oil from the contact surface.
Make sure that the gasket is installed in the correct direction.
19.
INSTALL CYLINDER HEAD SUB-ASSEMBLY
HINT:
The cylinder head set bolts are tightened in 2 progressive steps.
Apply a light coat of engine oil to the bolt threads and the area beneath the bolt heads that come in contact with the washers.
Install the bolts and plate washers to the cylinder head.
NOTICE:
Do not drop the washers into the cylinder head.
Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.
Torque:
70 N*m{
714 kgf*cm
, 52 ft.*lbf
}
Mark the front side of the cylinder head set bolt with paint.
Retighten the cylinder head set bolts 90° in the order shown in the illustration.
Check that the paint mark is now at a 90° angle to the front.
20.
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Apply a light coat of engine oil to a new O-ring, then install it onto the camshaft timing oil control valve.
Install the camshaft timing oil control valve with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
21.
INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.
Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.
NOTICE:
Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).
Check that there is no clearance between the gear and camshaft.
Tighten the flange bolt with the camshaft timing gear fixed in place.
Torque:
54 N*m{
551 kgf*cm
, 40 ft.*lbf
}
Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.
22.
INSTALL CAMSHAFT TIMING SPROCKET
Clamp the camshaft in a vise.
Tighten the flange bolt with the camshaft timing sprocket fixed.
Torque:
54 N*m{
551 kgf*cm
, 40 ft.*lbf
}
23.
INSTALL NO. 1 CAMSHAFT BEARING
Install the No. 1 camshaft bearing.
24.
INSTALL NO. 2 CAMSHAFT BEARING
Install the No. 2 camshaft bearing.
25.
INSTALL CAMSHAFT
Apply a light coat of engine oil to the journal portion of the camshaft.
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
No. 1 bearing cap:
30 N*m{
306 kgf*cm
, 22 ft.*lbf
}
No. 3 bearing cap:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
26.
INSTALL NO. 2 CAMSHAFT
Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Torque:
No. 2 bearing cap:
30 N*m{
306 kgf*cm
, 22 ft.*lbf
}
No. 3 bearing cap:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
27.
INSTALL KEYS
Install the 2 keys.
28.
INSTALL NO. 2 CHAIN SUB-ASSEMBLY
Set the crankshaft key into the left horizontal position.
Turn the drive shaft so that the cutout faces upward.
Align the yellow mark links with the timing marks of each gear as shown in the illustration.
Install the gears onto the crankshaft and oil pump shaft with the chain on the gears.
Temporarily tighten the oil pump drive shaft gear with the nut.
Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.
Torque:
12 N*m{
122 kgf*cm
, 9 ft.*lbf
}
Align the adjusting hole of the oil pump drive shaft gear with the groove of the oil pump.
Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.
Torque:
30 N*m{
301 kgf*cm
, 22 ft.*lbf
}
Rotate the crankshaft clockwise 90°, and position the crankshaft key to face up as shown in the illustration.
29.
INSTALL CRANKSHAFT TIMING SPROCKET
Install the crankshaft timing sprocket.
30.
INSTALL NO. 1 CHAIN VIBRATION DAMPER
Install the chain vibration damper with the 2 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
31.
INSTALL CHAIN SUB-ASSEMBLY
Set the No. 1 cylinder to TDC/compression.
Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
Using the crankshaft pulley bolt, turn the crankshaft to position the crankshaft key to face up as shown in the illustration.
Install the chain onto the crankshaft timing sprocket with the gold or pink mark link aligned with the timing mark on the crankshaft.
Using SST and a hammer, tap in the crankshaft timing sprocket.
SST
09309-37010
Align the gold or yellow mark link with each timing mark located on the camshaft timing gear and sprocket, then install the chain.
32.
INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper with the bolt.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
33.
INSTALL TIMING CHAIN GUIDE
Install the timing chain guide with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
34.
INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Install the sensor plate with the "F" mark facing forward.
35.
INSTALL TIMING CHAIN CASE OIL SEAL
Using SST, tap in a new oil seal until its surface is flush with the timing chain cover edge.
SST
09223-22010
Apply a light coat of MP grease to the lip of the oil seal.
NOTICE:
Keep the gap between the timing chain cover edge and the oil seal free of foreign matter.
36.
INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
Apply seal packing (diameter: 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
Apply seal packing in a continuous bead as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent
NOTICE:
Remove any oil from the contact surface.
Install the chain cover within 3 minutes after applying seal packing.
Do not start the engine for at least 2 hours after installing.
Install the timing chain cover with the 12 bolts and 2 nuts.
Torque:
Bolt A:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Bolt B:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
Bolt C:
55 N*m{
561 kgf*cm
, 41 ft.*lbf
}
Nut:
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
Bolt length
Item
Length
Bolt A
30 mm (1.18 in.) length for 10 mm head
Bolt B
30 mm (1.18 in.) length for 12 mm head
Bolt C
40 mm (1.57 in.) length for 14 mm head
Using a E10 "torx" socket, install the stud bolt to the drive belt tensioner.
Torque:
22 N*m{
220 kgf*cm
, 16 ft.*lbf
}
37.
INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Install the V-ribbed belt tensioner with the bolt and nut.
Torque:
60 N*m{
607 kgf*cm
, 44 ft.*lbf
}
NOTICE:
Do not lift the engine more than necessary.
38.
INSTALL OIL PAN SUB-ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.
Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
NOTICE:
Remove any oil from the contact surfaces.
Install the oil pan within 3 minutes after applying seal packing.
Do not start the engine for at least 2 hours after installing the oil pan.
Install the oil pan to the cylinder block.
Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
39.
INSTALL OIL PAN DRAIN PLUG
Install a new gasket and oil pan drain plug.
Torque:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
40.
INSTALL WATER PUMP ASSEMBLY
Remove any old seal packing material from the contact surface.
Apply a continuous line of seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter:
2.2 to 2.5 mm (0.09 to 0.10 in.)
NOTICE:
Remove any oil from the contact surface.
The parts must be set within 3 minutes after applying seal packing. Otherwise, the material must be removed and reapplied.
Install the water pump and clamp bracket with the 4 bolts and 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Install the wire of the crankshaft position sensor onto the clamp bracket.
Install the clamp of the crankshaft position sensor onto the water pump.
41.
INSTALL WATER PUMP PULLEY
Using SST, install the water pump pulley with the 4 bolts.
SST
09960-10010
(09962-01000, 09963-00700)
Torque:
26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
42.
INSTALL CRANKSHAFT POSITION SENSOR
Apply a light coat of engine oil to the O-ring of the sensor.
Confirm that the wire harness of the sensor is placed as shown in the illustration.
Install the sensor with the 2 bolts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Install the clamp of the crankshaft position sensor onto the water pump.
43.
INSTALL CRANKSHAFT PULLEY
Align the pulley set key with the key groove of the pulley.
Using SST, hold the pulley in place and tighten the bolt.
SST
09213-54015
(91651-60855)
09330-00021
Torque:
180 N*m{
1,835 kgf*cm
, 133 ft.*lbf
}
44.
INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Release the ratchet pawl, then fully push in the plunger and put the hook to the pin so that the plunger is in the position shown in the illustration.
Install a new gasket and the chain tensioner with the 2 nuts.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
NOTICE:
If the hook releases the plunger while the chain tensioner is being installed, set the hook again.
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
Turn the crankshaft clockwise, then check that the plunger is extended.
45.
INSPECT VALVE CLEARANCE
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Standard valve clearance (cold):
Item
Standard Condition
Intake
0.19 to 0.29 mm (0.0075 to 0.0114 in.)
Exhaust
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to TDC/compression.
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Standard valve clearance (cold):
Item
Standard Condition
Intake
0.19 to 0.29 mm (0.0075 to 0.0114 in.)
Exhaust
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
0.40 mm (0.0158 in.) - 0.24 mm (0.0095 in.) = 0.16 mm (0.0063 in.)
Measured used lifter thickness = 5.250 mm (0.2067 in.)
New lifter thickness = 5.410 mm (0.2130 in.) (Excess clearance + Used lifter thickness = Ideal new lifter)
0.16 mm (0.0063 in.) + 5.250 mm (0.2067 in.) = 5.410 mm (0.2130 in.)
Closest new lifter = 5.420 mm (0.2134 in.)
Select No. 42 lifter
Select a new lifter with a thickness as close as possible to the calculated values.
HINT:
Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 to 5.740 mm (0.1992 to 0.2260 in.).
The identification number inside the valve lifters shows the value to 2 decimal places. (The illustration shows 5.420 mm (0.2134 in.))
Valve lifter selection chart (intake).
New lifter thickness
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
06
5.060 (0.1992)
30
5.300 (0.2087)
54
5.540 (0.2181)
08
5.080 (0.2000)
32
5.320 (0.2094)
56
5.560 (0.2189)
10
5.100 (0.2008)
34
5.340 (0.2102)
58
5.580 (0.2197)
12
5.120 (0.2016)
36
5.360 (0.2110)
60
5.600 (0.2205)
14
5.140 (0.2024)
38
5.380 (0.2118)
62
5.620 (0.2213)
16
5.160 (0.2031)
40
5.400 (0.2126)
64
5.640 (0.2220)
18
5.180 (0.2039)
42
5.420 (0.2134)
66
5.660 (0.2228)
20
5.200 (0.2047)
44
5.440 (0.2142)
68
5.680 (0.2236)
22
5.220 (0.2055)
46
5.460 (0.2150)
70
5.700 (0.2244)
24
5.240 (0.2063)
48
5.480 (0.2157)
72
5.720 (0.2252)
26
5.260 (0.2071)
50
5.500 (0.2165)
74
5.740 (0.2260)
28
5.280 (0.2079)
52
5.520 (0.2173)
-
-
Standard intake valve clearance (cold):
0.19 to 0.29 mm (0.0075 to 0.0114 in.)
EXAMPLE: The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0157 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 42 lifter.
Valve lifter selection chart (exhaust).
New lifter thickness
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
Lifter No.
Thickness mm (in.)
06
5.060 (0.1992)
30
5.300 (0.2087)
54
5.540 (0.2181)
08
5.080 (0.2000)
32
5.320 (0.2094)
56
5.560 (0.2189)
10
5.100 (0.2008)
34
5.340 (0.2102)
58
5.580 (0.2197)
12
5.120 (0.2016)
36
5.360 (0.2110)
60
5.600 (0.2205)
14
5.140 (0.2024)
38
5.380 (0.2118)
62
5.620 (0.2213)
16
5.160 (0.2031)
40
5.400 (0.2126)
64
5.640 (0.2220)
18
5.180 (0.2039)
42
5.420 (0.2134)
66
5.660 (0.2228)
20
5.200 (0.2047)
44
5.440 (0.2142)
68
5.680 (0.2236)
22
5.220 (0.2055)
46
5.460 (0.2150)
70
5.700 (0.2244)
24
5.240 (0.2063)
48
5.480 (0.2157)
72
5.720 (0.2252)
26
5.260 (0.2071)
50
5.500 (0.2165)
74
5.740 (0.2260)
28
5.280 (0.2079)
52
5.520 (0.2173)
-
-
Standard exhaust valve clearance (cold):
0.30 to 0.40 mm (0.0118 to 0.0157 in.)
EXAMPLE: The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.430 mm (0.0169 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 42 lifter.
Install the selected valve lifter.
47.
INSTALL CAMSHAFT POSITION SENSOR
Apply a light coat of engine oil to the O-ring of the sensor.
Install the sensor with the bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
48.
INSTALL CYLINDER HEAD COVER GASKET
Install the gasket to the cylinder head cover.
NOTICE:
Remove any oil from the contact surface.
49.
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Apply seal packing to the 2 locations shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after installing the cylinder head cover.
Install the cylinder head cover with the 8 bolts and 2 nuts.
Torque:
Bolt A:
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
Bolt B:
14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
Nut:
11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
Install the 2 engine wires with the 2 bolts.
Torque:
8.4 N*m{
86 kgf*cm
, 74 in.*lbf
}
50.
INSTALL OIL COOLER ASSEMBLY
Clean the oil cooler contact surface on the cooler mounting.
Install a new O-ring to the oil cooler.
Apply a light coat of engine oil to the threads and under the head of the union bolt.
Install the oil cooler with the plate washer, oil filter union and nut.
Torque:
Oil Filter Union:
79 N*m{
806 kgf*cm
, 58 ft.*lbf
}
Nut:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
Apply adhesive to the threads of the oil filter union.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the union bolt.
Torque:
25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
51.
INSTALL OIL FILTER SUB-ASSEMBLY
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
When using a torque wrench:
Using SST, tighten the oil filter.
SST
09228-06501
Torque:
13 N*m{
133 kgf*cm
, 10 ft.*lbf
}
When not using a torque wrench:
Using SST, tighten it an additional 3/4 turn.
SST
09228-06501
52.
INSTALL SPARK PLUG
Install the spark plugs.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
53.
INSTALL VENTILATION VALVE SUB-ASSEMBLY
Apply adhesive to the threads of the ventilation valve.
Install the ventilation valve.
Torque:
19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent