2006-2011 Camry Aurion · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jun 2006


1. INSTALL INTAKE VALVE GUIDE BUSH

  1. A131495
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush size
    Bush bore diameter
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A036634E03
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.6 to 10.0 mm (0.3779 to 0.3937 in.)

  1. A136150
    Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)


2. INSTALL EXHAUST VALVE GUIDE BUSH

  1. A124782
    Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush size
    Bush bore diameter
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A036635E03
    Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.6 to 10.0 mm (0.3779 to 0.3937 in.)

  1. A124783
    Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)


3. INSTALL RING PIN

  1. A128230E01
    Using a plastic-faced hammer, tap in a new ring pin to the specified protrusion height.

    Protrusion height:
    3 mm (0.12 in.)


4. INSTALL STUD BOLT

NOTICE:
If the stud bolt is deformed or the threads are damaged, replace it.

  1. Using E5 and E7 "TORX" sockets, install the stud bolts.

    A128231E01

    Torque:
    Bolt A:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Bolt B:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    Bolt C:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Bolt D:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }


5. INSTALL NO. 1 STRAIGHT SCREW PLUG

  1. A062841
    Using a 14 mm straight hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.


6. INSTALL VALVE SPRING SEAT

  1. A062872
    Install the valve spring seats to the cylinder head.


7. INSTALL VALVE STEM OIL SEAL

  1. A052449E01
    Apply a light coat of engine oil to a new oil seal.

    NOTICE:
    Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.

    HINT:
    The intake valve oil seal is gray and the exhaust valve oil seal is black.

  1. A129854E01
    Using SST, push in the oil seal.
    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.


8. INSTALL INTAKE VALVE

  1. A094935E04
    Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A128225E01
    Using SST and wooden blocks, compress the spring and install the 2 retainer locks.
    SST
    09202-70020   (09202-00010)

  1. A036640E01
    Using a 5 mm pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.


9. INSTALL EXHAUST VALVE

  1. A094936E03
    Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.

  1. Install the valve, compression spring and spring retainer to the cylinder head.

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A128226E01
    Using SST and wooden blocks, compress the spring and install the 2 retainer locks.
    SST
    09202-70020   (09202-00010)

  1. A036641E01
    Using a 5 mm pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.


10. INSTALL VALVE LIFTER

  1. A062842E01
    Apply a light coat of engine oil to the tip of each valve stem.

  1. Install the valve lifters.

    NOTICE:
    Install the valve lifters in their original places.

← INSPECTION (from Jun 2009)INSTALLATION (Jun 2006 – Sep 2006) →