2006-2011 Camry Aurion · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used.
If not, the cable may become hot and cause injury.

NOTICE:
These tests must be performed within 3 to 5 seconds to avoid burning out the coil.

  1. Perform a pull-in test.

    1. Remove the nut and disconnect the lead wire from terminal C.

    2. A197192E01
      Connect a battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. A197193E01
    Perform a hold-in test.

    1. Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.

  1. A197194E01
    Check the clutch pinion gear return.

    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.
      If the clutch pinion gear does not return, replace the magnet starter switch assembly.

  1. A197195E01
    Perform a no-load performance test.

    1. Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Clamp the starter in a vise.

      NOTICE:
      Ensure that the starter is secured firmly in the vise to prevent it from falling out.

    3. Connect the battery and an ammeter to the starter as shown in the illustration.

      NOTICE:
      Do not allow any lead to get caught as the pinion gear operates.

    4. Check that the starter operates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Standard current:
      90 A or less at 11.5 V

      If the result is not as specified, repair or replace the starter assembly.


INSPECT STARTER CLUTCH

  1. A197200E01
    Check the starter clutch.

    1. Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
      If necessary, replace the repair service starter kit.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A197181
    Inspect the plunger for an open circuit.

    1. Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.

  1. A197182E01
    Inspect the pull-in coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A197183E03
    Inspect the hold-in coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.


INSPECT STARTER ARMATURE ASSEMBLY

HINT:
If these is no continuity between any segments, replace the starter armature assembly.

  1. Check the surface of the commutator for dirt and burns.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

  1. Inspect the commutator for an open circuit.

    1. A058372E13
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.

  1. Inspect the commutator for a short circuit.

    1. A058373E09
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator - Armature coil core
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter armature assembly.

  1. A194765E01
    Using a vernier caliper, measure the commutator length.

    Standard length:
    3.1 mm (0.122 in.)

    Maximum length:
    3.8 mm (0.149 in.)

    If the length is more than the maximum, replace the starter armature assembly.


INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

  1. A194766E01
    Using a vernier caliper, measure the brush length.

    Standard length:
    9.0 mm (0.354 in.)

    Minimum length:
    4.0 mm (0.158 in.)

    If the length is less than the minimum, replace the starter commutator end frame assembly.

  1. A197190E01
    Inspect the insulation.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush - Negative (-) brush
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter commutator end frame assembly.

← INSPECTION (Jun 2006 – May 2009)REASSEMBLY (Jun 2006 – May 2009) →