2006-2011 Camry Aurion · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Pass the transmission control cable assembly from the cabin to the engine compartment.

  1. Install the No. 2 shift cable grommet retainer to the transmission control cable assembly.

  1. C132234
    Install the No. 2 shift cable grommet retainer with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. C135020
    Install the transmission control cable assembly as shown in the illustration.

    HINT:
    1. Install the floor shift cable with the uneven surface facing up.
    2. Securely engage the claws of the floor shift cable.

  1. C090579
    Connect the control cable to the control cable clamp.

  1. C135705
    Connect the control cable to the bracket with a new clip.

  1. C135109
    Install the transmission control cable to the control shaft lever with the nut.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. C138300E02
    Push in the lock piece of the transmission control cable.

    NOTICE:
    Firmly push in the lock piece until the slider lock is engaged.

    HINT:
    After pushing in the lock piece, make sure that the boot is not deformed.


2. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A134905
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose clamp.


3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A135670
    Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.

  1. A236553E01
    Connect the No. 1 air cleaner hose to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    1. Match each concave area concavity of the air cleaner hose with the bolt of the throttle body.
    2. Make sure that the hose clamp is at the correct angle.

  1. A146036
    Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A135666E02
    Connect the purge line hose to the clamp (*1).

  1. Connect the 2 purge VSV vacuum hoses (*2).

  1. Connect the purge VSV connector (*3).

  1. Connect the mass air flow meter connector (*4).


4. INSTALL AIR CLEANER INLET ASSEMBLY

  1. A134903
    Install the air cleaner inlet with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


5. INSTALL BATTERY
  1. Install the battery and battery tray.

  1. A134906
    Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Nut:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


6. INSTALL AIR CONDITIONING UNIT

HINT:
(Click here).


7. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch to the ON position and brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position.
    If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


8. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.

  1. C135109
    Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.

  1. C135711
    Push the control shaft lever fully downward.

  1. Return the control shaft lever 2 notches to the N position.

  1. C135734E02
    Move the slider in the direction indicated by arrow A and pull up the lock piece in the direction indicated by arrow B.

    NOTICE:
    Do not damage the boot.

  1. C135109
    Install the transmission control cable to the control shaft lever with the nut.

    Torque:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }

    NOTICE:
    1. If the control cable end is excessively pushed up, the shift lever cannot be adjusted.
    2. When tightening the nut, confirm that the control cable is properly stretched.

  1. C138300E01
    Push in the lock piece.

    NOTICE:
    Firmly push in the lock piece until the slider lock is engaged.

    HINT:
    After pushing the lock piece make sure that the boot is not deformed.

  1. Start the engine and make sure that the vehicle moves forward when moving the shift lever from the N to the D position and moves rearward when moving it to the R position.
    If it becomes hard to move the shift lever, readjust the shift lever position.

← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →