DISASSEMBLY
Removal / installation · Vehicles built from Jun 2006
| 1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Remove the nut, washer, and control shaft lever.

Using a screwdriver, unstake the lock plate, and remove the lock nut and lock plate.

Remove the 2 bolts and pull out the park/neutral position switch.

| 2. REMOVE NO. 2 BREATHER PLUG |
Remove the No. 2 breather plug from the transaxle case.

Remove the hose and O-ring from the No. 2 breather plug.

| 3. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION) |
Remove the union.

Remove the O-ring from the union.
| 4. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION) |
Remove the union.

Remove the O-ring from the union.
| 5. REMOVE SPEED SENSOR |
Remove the 2 bolts and the 2 speed sensors from the transaxle assembly.

| 6. REMOVE NO. 1 TRANSAXLE CASE PLUG |
Remove the 4 No. 1 transaxle case plugs from the transaxle case.

Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.
| 7. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY |
Support the transaxle assembly.

| 8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY |
Remove the drain plug and drain plug gasket from the oil pan.
Remove the 18 bolts, oil pan, and gasket.

Remove the 2 transmission oil cleaner magnets from the oil pan.

| 9. INSPECT TRANSMISSION OIL CLEANER MAGNET |
Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle.

- Result:
- Steel (magnetic):
- bearing, gear, and plate wear
- Brass (non-magnetic):
- bushing wear
| 10. DISCONNECT TRANSMISSION WIRE |
Disconnect the 7 connectors from the shift solenoid valves.

Remove the bolt, lock plate, and ATF temperature sensor.
| 11. REMOVE TRANSMISSION WIRE |
Remove the bolt and transmission wire from the transaxle case.

| 12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY |
Remove the 3 bolts and oil strainer.

Remove the O-ring from the oil strainer.

| 13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY |
Support the valve body assembly and remove the 17 bolts and valve body assembly.

| 14. REMOVE NO. 1 GOVERNOR APPLY GASKET |
Remove the No. 1 governor apply gasket from the transaxle case.

| 15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET |
Remove the transaxle case 2nd brake gasket from the transaxle case.

| 16. REMOVE BRAKE DRUM GASKET |
Remove the brake drum gasket from the transaxle case.

| 17. REMOVE CHECK BALL BODY |
Remove the check ball body and spring from the transaxle case.

| 18. REMOVE C-3 ACCUMULATOR PISTON |
Remove the spring from the C-3 accumulator piston.

Using needle-nose pliers, remove the C-3 accumulator piston from the transaxle case.

Remove the O-ring from the C-3 accumulator piston.

| 19. REMOVE REVERSE CLUTCH ACCUMULATOR PISTON |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the reverse accumulator piston and spring.

- NOTICE:
- Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
- Take care not to splash ATF when applying the air.
- Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
Remove the 2 O-rings from the reverse clutch accumulator piston.

| 20. REMOVE B-3 ACCUMULATOR PISTON |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

- NOTICE:
- Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
- Take care not to splash ATF when applying the air.
- Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
Remove the O-ring from the B-3 accumulator piston.

| 21. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING |
Using needle-nose pliers, remove the manual valve lever shaft retainer spring.

| 22. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY |
Remove the 2 bolts and manual detent spring sub-assembly.

| 23. REMOVE PARKING LOCK PAWL BRACKET |
Remove the 2 bolts and parking lock pawl bracket.

| 24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY |
Using a screwdriver, slide the spacer.

Using a pin punch (φ3 mm) and hammer, drive out the pin.

- HINT:
- Slowly drive out the pin so that it will not fall into the transaxle case.
Remove the manual valve lever shaft, manual valve lever, and spacer.

| 25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY |
Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.

- HINT:
- Align the dial with the notches on the manual valve lever sub-assembly to remove the parking lock rod sub-assembly.
| 26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL |
Using a screwdriver, remove the oil seal from the transaxle case.

| 27. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY |
Support the transaxle case with the oil pump side facing up.
| 28. INSPECT INPUT SHAFT END PLAY |
Using a dial indicator, measure the input shaft end play.

- End play:
- 0.262 to 1.244 mm (0.01 to 0.049 in.)
| 29. REMOVE TRANSAXLE HOUSING |
Remove the 18 bolts.

Tap on the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.
- NOTICE:
- The differential may be accidentally removed when the transaxle housing is removed.
| 30. REMOVE OIL PUMP ASSEMBLY |
Remove the 7 bolts and oil pump from the transaxle case.

| 31. REMOVE THRUST NEEDLE ROLLER BEARING |
Remove the thrust needle roller bearing from the underdrive planetary gear assembly.

| 32. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE |
Remove the No. 2 thrust bearing underdrive race from the underdrive planetary gear assembly.

| 33. REMOVE DIFFERENTIAL GEAR ASSEMBLY |
Remove the differential gear assembly from the transaxle case.

| 34. REMOVE OVERDRIVE BRAKE GASKET |
Remove the 2 overdrive brake gaskets from the transaxle case.

| 35. REMOVE FORWARD CLUTCH ASSEMBLY |
Remove the forward clutch assembly from the transaxle case.

Remove the thrust needle roller bearing from the forward clutch.

| 36. REMOVE MULTIPLE DISC CLUTCH HUB |
Remove the thrust needle roller bearing, multiple disc clutch hub, thrust needle roller bearing and No. 1 thrust bearing race from the transaxle case.

| 37. INSPECT MULTIPLE DISC CLUTCH HUB |
Using a dial indicator, measure the inside diameter of the multiple disc clutch hub bushing.

- Standard inside diameter:
- 23.025 to 23.046 mm (0.9065 to 0.9073 in.)
- Maximum inside diameter:
- 23.09 mm (0.9091 in.)
- NOTICE:
- Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discoloration is identified, replace the direct clutch sub-assembly with a new one.
| 38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY |
Remove the bolt and pawl shaft clamp from the transaxle case.

Remove the parking lock pawl shaft from the transaxle case.

Push the parking lock pawl.

- HINT:
- Failure to do so will cause interference when the underdrive planetary gear is removed.
Remove the underdrive planetary gear assembly from the transaxle case.

- NOTICE:
- Do not drop the underdrive planetary gear assembly.
| 39. REMOVE PARKING LOCK PAWL |
Remove the spring, pawl pin and parking lock pawl.

| 40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY |
Remove the underdrive clutch assembly, thrust bearing, and bearing race from the transaxle case.

| 41. REMOVE UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY |
Using a screwdriver, remove the snap ring from the transaxle case.

Remove the underdrive one-way clutch from the transaxle case.

Remove the outer race retainer from the one-way clutch.

| 42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC |
Using a screwdriver, remove the snap ring.

Remove the flange, 3 discs and 3 plates from the transaxle case.

| 43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC |
Check if the sliding surfaces of the discs, plates and flange are worn or burnt.

If necessary, replace them.- NOTICE:
- If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
- Before assembling new discs, soak them in ATF for at least 15 minutes.
- If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
| 44. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY |
Remove the 11 bolts.

Tap on the circumference of the rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.
| 45. REMOVE NO. 1 TRANSAXLE CASE PLUG |
Remove the 4 No. 1 transaxle case plugs from the transaxle rear cover.

Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.
| 46. REMOVE REAR CLUTCH OIL SEAL RING |
Remove the 3 rear clutch oil seal rings from the transaxle rear cover.

| 47. REMOVE NEEDLE ROLLER BEARING |
Using SST, remove the needle roller bearing from the transaxle rear cover.

- SST
- 09387-00041
(09387-01021, 09387-01030, 09387-01040)
| 48. REMOVE NO. 1 GOVERNOR APPLY GASKET |
Using a screwdriver, remove the 3 apply gaskets.

| 49. REMOVE BRAKE APPLY TUBE |
Remove the bolt, clamp and brake apply tube.

Remove the clutch apply tube.
Remove the brake apply tube from the clamp.
| 50. REMOVE DIRECT CLUTCH ASSEMBLY |
Remove the thrust bearing and the direct clutch assembly from the transaxle case.

| 51. INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
Install the intermediate shaft and needle roller bearing on the transaxle rear cover.

- NOTICE:
- Be careful not to damage the oil seal ring outers.
Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
- Pack clearance:
- 0.60 to 0.82 mm (0.02362 to 0.03228 in.)
| 52. INSPECT PACK CLEARANCE OF OVERDRIVE CLUTCH |
Using a dial indicator, measure the overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

- Pack clearance:
- 0.52 to 0.83 mm (0.02047 to 0.03268 in.)
| 53. REMOVE DIRECT MULTIPLE DISC CLUTCH DISC |
Using a screwdriver, remove the snap ring from the intermediate shaft.

Remove the flange, 3 discs, 3 plates and cushion plate from the intermediate shaft.

| 54. INSPECT DIRECT MULTIPLE DISC CLUTCH DISC |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

- NOTICE:
- If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
- Before assembling new discs, soak them in ATF for at least 15 minutes.
- If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
| 55. REMOVE OVERDRIVE DIRECT CLUTCH DISC |
Using a screwdriver, remove the snap ring from the intermediate shaft.

Remove the flange, 3 discs and 3 plates from the intermediate shaft.
| 56. INSPECT OVERDRIVE DIRECT CLUTCH DISC |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

- NOTICE:
- If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
- Before assembling new discs, soak them in ATF for at least 15 minutes.
- If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
| 57. REMOVE OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY |
Place SST on the clutch balancer and compress the spring with a press.

- SST
- 09387-00020
Using a snap ring expander, remove the snap ring from the direct clutch drum.
- NOTICE:
- Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
- Do not expand the snap ring excessively.
- Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
Remove the clutch balancer from the overdrive direct clutch drum.

Remove the overdrive clutch return spring from the overdrive direct clutch drum.

| 58. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY |
Using vernier calipers, measure the free length of the spring together with the spring seat.

- Standard free length:
- 25.91 mm (1.0201 in.)
| 59. REMOVE OVERDRIVE DIRECT CLUTCH PISTON |
Install the intermediate shaft on the transaxle rear cover.

Holding the direct clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the direct clutch piston.
| 60. REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY |
Holding the direct clutch drum by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the direct clutch drum.

| 61. REMOVE OVERDRIVE DIRECT CLUTCH O-RING |
Using a screwdriver, remove the O-ring from the direct clutch drum.

| 62. REMOVE OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY |
Remove the thrust bearing race, thrust bearing, and overdrive direct clutch hub from the planetary gear assembly.

| 63. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY |
Remove the rear planetary sun gear assembly from the transaxle case.

Remove the thrust needle roller bearing and thrust bearing race from the rear planetary sun gear assembly.

Remove the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.

| 64. REMOVE ONE-WAY CLUTCH ASSEMBLY |
Remove the one-way clutch assembly and the thrust needle roller bearing from the transaxle case.

Remove the one-way clutch inner race from the one-way clutch assembly.

| 65. REMOVE ONE-WAY CLUTCH SLEEVE |
Remove the one-way clutch sleeve from the transaxle case.

| 66. REMOVE NO. 1 PLANETARY CARRIER THRUST WASHER |
Remove the No. 1 planetary carrier thrust washer from the planetary gear assembly.

| 67. REMOVE 2ND BRAKE DISC |
Using a screwdriver, remove the snap ring.

Remove the flange, 3 discs and 3 plates from the transaxle case.
| 68. INSPECT 2ND BRAKE DISC |
Check if the sliding surfaces of the discs, plates and flange are worn or burnt.

If necessary, replace them.- NOTICE:
- If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
- Before assembling new discs, soak them in ATF for at least 15 minutes.
- If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
| 69. REMOVE SECOND BRAKE PISTON ASSEMBLY |
Using a screwdriver, remove the snap ring.

Remove the second brake piston assembly from the transaxle case.

| 70. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
Place SST on the return spring and compress it with a press.

- SST
- 09387-00060
Using a screwdriver, remove the snap ring.
Remove the 2nd brake piston return spring sub-assembly.

| 71. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
Using vernier calipers, measure the free length of the spring together with the spring seat.

- Standard free length:
- 16.61 mm (0.6539 in.)
| 72. REMOVE 2ND BRAKE PISTON |
Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.

| 73. REMOVE 2ND BRAKE PISTON O-RING |
Remove the 2 O-rings from the 2nd brake piston.

| 74. REMOVE REAR PLANETARY GEAR ASSEMBLY |
Using a screwdriver, remove the snap ring.

Remove the rear planetary gear assembly from the transaxle case.

| 75. REMOVE INPUT SUN GEAR |
Remove the 2 thrust needle roller bearings, No. 2 thrust bearing races, No. 3 thrust bearing race, and input sun gear from the transaxle case.

| 76. REMOVE 1ST AND REVERSE BRAKE DISC |
Remove the flange, 5 discs and 5 plates from the transaxle case.

| 77. INSPECT 1ST AND REVERSE BRAKE DISC |
Check if the sliding surfaces of the discs, plates and flange are worn or burnt.

If necessary, replace them.- NOTICE:
- If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
- Before assembling new discs, soak them in ATF for at least 15 minutes.
- If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
| 78. REMOVE FRONT PLANETARY GEAR ASSEMBLY |
Using a chisel and hammer, unstake the lock washer.

- NOTICE:
- Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut, and the nut cannot be loosened.
Using SST, remove the nut and washer.

- SST
- 09387-00030
09387-00080
Using SST and a press, remove the front planetary gear assembly from the counter drive gear.

- SST
- 09950-60010
(09951-00450)
09950-70010 (09951-07100)
Remove the front planetary gear assembly from the brake hub.

| 79. REMOVE FRONT PLANETARY RING GEAR |
Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.

| 80. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
Place SST on the return spring, and compress the return spring with a press.

- SST
- 09387-00070
Using a snap ring expander, remove the snap ring.
- NOTICE:
- Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
- Do not expand the snap ring excessively.
- Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
Remove the return spring.
| 81. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
Using vernier calipers, measure the free length of the spring together with the spring seat.

- Standard free length:
- 17.63 mm (0.6941 in.)
| 82. REMOVE 1ST AND REVERSE BRAKE PISTON |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

- NOTICE:
- Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
- Take care not to splash ATF when applying the air.
- Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
Remove the 2 O-rings from the 1st and reverse brake piston.

| 83. REMOVE COUNTER DRIVE GEAR |
Using SST and a press, remove the counter drive gear from the transaxle case.

- SST
- 09950-60010
(09951-00590)
09950-70010 (09951-07100)
Tighten the 2 bolts evenly and make a clearance of approx. 20.0 mm (0.797 in.) between the counter drive gear and the inner race.

Using SST, remove the tapered roller bearing inner race.

- SST
- 09950-00020
09950-00030
09950-60010 (09951-00590)
| 84. REMOVE COUNTER DRIVE ANGULAR BALL BEARING |
Remove the bearing inner race (rear side) and angular ball (rear side).

Using SST, remove the bearing outer race (rear side) from the transaxle case.

- SST
- 09308-00010
Remove the angular ball (front side).

Using SST and a press, remove the bearing outer race (front side) from the transaxle case.

- SST
- 09950-60020
(09951-00810)
09950-70010 (09951-07200)
Using a screwdriver, remove the snap ring from the transaxle case.

| 85. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
Place SST on the return spring, and compress the return spring with a press.

- SST
- 09387-00020
Using a snap ring expander, remove the snap ring.
- NOTICE:
- Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
- Do not expand the snap ring excessively.
- Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
Remove the return spring.
| 86. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
Using vernier calipers, measure the free length of the spring together with the spring seat.

- Standard free length:
- 13.24 mm (0.5213 in.)
| 87. REMOVE UNDERDRIVE BRAKE PISTON |
Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.

Remove the 2 O-rings from the underdrive brake piston.

| 88. REMOVE NEEDLE ROLLER BEARING |
Using SST, remove the needle roller bearing from the transaxle case.

- SST
- 09387-00041
(09387-01010, 09387-01030, 09387-01040)
| 89. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING |
Remove the 2 oil seal rings from the transaxle case.

| 90. REMOVE NO. 1 TRANSAXLE CASE PLUG |
Remove the 2 No. 1 transaxle case plugs.

Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.
| 91. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING |
Using SST, remove the underdrive cylindrical roller bearing from the transaxle case.

- SST
- 09820-00031
09950-40011 (09952-04010, 09954-04010, 09955-04061, 09957-04010)
09950-50013 (09951-05010, 09953-05020)
| 92. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING |
Remove the oil seal ring from the transaxle housing.

| 93. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE |
Remove the bolt, transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.

