REASSEMBLY
Removal / installation · Vehicles built from Jun 2006
| 1.
INSTALL REVERSE GEAR |
 |
- Coat the reverse gear with gear oil.
Install the 3 No. 1 synchromesh shifting key springs and No. 1 transmission clutch hub to the reverse gear.
- NOTICE:
- Assemble the reverse gear and the No. 1 transmission clutch hub in the correct direction.
Using a screwdriver, install the 3 No. 1 synchromesh shifting keys to the reverse gear.
| 2.
INSTALL OUTPUT SHAFT FRONT BEARING |
 |
- Using SST and a press, install the output shaft front bearing (inner race) to the output shaft.
- SST
- 09950-60010
(09951-00430)
09950-70010
(09951-07150)
| 3.
INSTALL NO. 1 SYNCHRONIZER RING SET |
 |
- Coat the No. 1 synchronizer ring set with gear oil and install it to the 1st gear.
- NOTICE:
- Align the No. 1 synchronizer ring set with the hole of the 1st gear.
| 4.
INSTALL 1ST GEAR NEEDLE ROLLER BEARING |
 |
- Coat the 1st gear needle roller bearing with gear oil and install it to the output shaft.
| 5.
INSTALL 1ST GEAR |
 |
- Coat the 1st gear with gear oil and install it to the output shaft.
| 6.
INSTALL NO. 1 TRANSMISSION CLUTCH HUB |
 |
- Using SST and a press, install the No. 1 transmission clutch hub to the output shaft.
- SST
- 09316-60011
(09316-00031)
09950-60010
(09951-00320)
09950-70010
(09951-07100)
- NOTICE:
- Align the No. 1 synchronizer ring with the No. 1 synchromesh shifting key.
- Make sure that the 1st gear rotates.
| 7.
INSTALL 2ND GEAR BUSHING BALL |
 |
- Coat the gear bushing with MP grease, and install it to the output shaft.
| 8.
INSTALL 2ND GEAR BUSHING |
 |
- Coat the 2nd gear bushing with gear oil and install it to the output shaft.
| 9.
INSTALL 2ND GEAR BEARING SPACER |
 |
- Coat the 2nd gear bearing spacer with gear oil and install it to the output shaft.
| 10.
INSTALL 2ND GEAR NEEDLE ROLLER BEARING |
 |
- Coat the 2nd gear needle roller bearing with gear oil and install it to the output shaft.
| 11.
INSTALL NO. 2 SYNCHRONIZER RING SET |
 |
- Coat the No. 2 synchronizer ring set with gear oil and install it to the No. 1 transmission clutch hub.
- NOTICE:
- Align the key groove on the No. 2 synchronizer ring set with the No. 1 synchromesh shifting key.
| 12.
INSTALL 2ND GEAR |
 |
- Coat the 2nd gear with gear oil and install it to the output shaft.
| 13.
INSTALL 3RD DRIVEN GEAR |
 |
- Using SST and a press, install the 3rd driven gear to the output shaft.
- SST
- 09608-00071
09950-60010
(09951-00320)
09950-70010
(09951-07100)
| 14.
INSTALL OUTPUT GEAR SPACER |
 |
- Install the output gear spacer to the output shaft.
| 15.
INSTALL 4TH DRIVEN GEAR |
 |
- Using SST and a press, install the 4th driven gear to the output shaft.
- SST
- 09608-00071
09950-60010
(09951-00320)
09950-70010
(09951-07100)
| 16.
INSTALL OUTPUT SHAFT FRONT BEARING |
 |
- Using SST and a press, install the output shaft front bearing (inner race) to the output shaft.
- SST
- 09506-30012
09950-60010
(09951-00320)
09950-70010
(09951-07100)