2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Headlight Relay Circuit

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009

DESCRIPTION

The main body ECU receives a signal from the headlight dimmer switch assembly, and turns the low beam headlights on.

HINT:
The headlight relays are built into the power distributor, so unlike conventional relays, they cannot be removed for inspection.


WIRING DIAGRAM

E211691E01

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester main switch on.

  1. Select the item below in the ACTIVE TEST and then check that the relays operate.

    Main Body (Main Body ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Relay
    Headlight Relays
    ON / OFF
    -

OK:
Headlight relays operate. (Low beam headlights illuminate.)



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

  1. E121528E05
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ID-3 (HRLY) - Body ground
    Light control switch OFF → HEAD
    10 to 14 V → Below 1 V



OK
Go to step 6
NG


3. CHECK HARNESS AND CONNECTOR (BATTERY - ENGINE ROOM J/B ASSEMBLY)

  1. B074501E17
    Disconnect the 1G engine room J/B assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connector
    Condition
    Specified Condition
    1G - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT ENGINE ROOM J/B BLOCK ASSEMBLY
  1. Reconnect the 1G engine room J/B assembly connector.

  1. E121531E01
    Disconnect the 1D engine room J/B assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1D-9 - Body ground
    Always
    10 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (POWER DISTRIBUTOR)
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM J/B ASSEMBLY - INSTRUMENT PANEL J/B ASSEMBLY)
  1. Reconnect the 1D engine room J/B assembly connectors.

  1. E121479E05
    Disconnect the ID instrument panel J/B assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ID-3 (HRLY) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

6. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

  1. E121533E01
    Remove the H-LP (RL) fuse and H-LP (LL) fuse from the engine room J/B assembly.

  1. Measure the voltage between the loading slot of each fuse and body ground.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    H-LP (RL) Terminal - Body ground
    Light control switch in HEAD
    10 to 14 V
    H-LP (LL) Terminal - Body ground
    Light control switch in HEAD
    10 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (POWER DISTRIBUTOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUSE - BODY GROUND)


← Headlight Relay Circuit (Jun 2006 – May 2009)Headlight (HI-BEAM) Circuit (Jun 2006 – May 2009) →